Running 12.2(22) IP services base on an old 3550. At the interface config level, if I type "no switchport" I get a config that reads "no switchport", if I type "no switchport mode" I get "switchport mode dynamic desirable" (the default for this parti...
Forum Posts
So we are gearing up to replace a netgear switch with a Cisco Catalyst 9300 and I have a few questions regarding the config between the switch and the firewall. The firewall acts as a DCHP server, DNS, and handles all routing so in our case the switc...
I'm racking my brains trying to figure out why, a Cisco product do not have EIGRP as an option for the router command. I am trying to implement EIGRP OTP to simplify our network, does anyone have any ideas how to enable the feature or does the C1000 ...
Resolved! fix 3850 CSCvc14038 Releases
Hi everyone, Our 3850 switches are encountering the bug of CSCvc14038.We want to upgrade the switches Known Fixed Releases:(6)16.6.1Everest-16.5.116.5.116.5(0.138) I can't find any releases about 16.5.1 or 16.5(0.138) in 3850 ,I think the releases a...
Hi,I am trying to setup ntp and summer-time on my 3172-tq switch with NX-OS 9.3.7aI already setup ntp and timezone for Italy (CET 1 0), but do not see how to prpoperly setup summer-time.We change the daylight saving time on last sunday (march, octobe...
Resolved! Radius on switch Catalyst
Hi, I have configured my switch Cisco Catalyst 2960 L ver.15.2(6) for login with Radius.aaa group server radius GRP-TESTserver name Present!aaa authentication login TEST group GRP-TEST localaaa authorization exec default localaaa authorization exec T...
Hello,I am new to scripting on Cisco switches, so I would need your help.On C1000 I am trying to create a tcl script that will shutdown all ports on the switch, if it receives Root guard blocking port Syslog message. From what I understand, this swit...
Hi, A customer has PLC devices that requires 10Mbit half-duplex to be configured on the switch ports. The switch ports are configured with 802.1x and MAB and the PLC gets authenticated based on MAC address in ISE. In ISE I push the radius attribute ...
Hi there, I need a little help here. I've been stuck while configuring Multicast Traffic for two VLANs 59 & 60. Actually, these VLANs belong to Security Systems, and they want to enable multicast traffic on the network devices (Switches (Layer 2 & 3)...
recently had an in chassis standby sup fail and be replaced via our support contractors, Can I confirm with the community that replacement is literally remove failed unit and install the new one? I stumbled across the following. documentation and the...
Resolved! Static Route cannot Reach Next Hop
i have a 3850 that directly connect to a firewall. i configured a default static route to the next hop ip which i configured on the firewall interface. I have ip routing enable. i configured "swichport mode trunk" on the cisco interface. I have multi...
Hi,I am replacing my 300 series switch with 9000 series switch. Previously, I have create a NPS to as the radius server to Authenticate the SSH login on those switches. But I find that the syntax on 9000 series are different. I am not sure what shoul...
Resolved! Nexus Switch 93128TX Booting Issue
Hi,I am getting below error after powering ON the switch. I have also attached the logs file for complete logs review.CISCO SWITCH Ver7.17Device detected on 0:6:0 after 0 msecsDevice detected on 0:1:1 after 0 msecsDevice detected on 0:1:0 after 0 mse...
Good day and thank you for reading!I have a small question, I created port channels, written the configurations, and assigned them to their specific interfaces. For some reason it's not passing through to the other interfaces. Everything seems to hav...
I've configured my Nexus 3172 for RADIUS authentication which is working, however, when I make the NPS (RADIUS) server unavailable either by stopping NPS service or disabling the RADIUS Client for this switch the fallback to local login isn't working...
