Dear All,At my office want to use main switch for traffice controller but i don't know the cisco model?Could you let me know the model?Main Switch (Traffic Controller) 24 ports 2-slot for 10/100 BAse TXBest Regards,Rechard
Hi,I have 7 numbers of 3750 Cisco Switch, they all are part of single stack. I found, there was flapping in the stack ports of Sw-3 (port-2) and Sw-4(port-1) which are directly connected with stack cable.I have replaced the stack cable with new one, ...
I'm connecting to a remote location and need to copy a few files off the flash to a host on the LAN so I can update them. I know to go from the lan to the flash I can usecopy tftp://host/filebut is it possible to do the same thing in reverse?
Hi,I have 3750 switch router which is configured with IP address and other stuff.The thing is that when i type sh runing config , i do not see the ports and other commands that i configured.however when i go to the interface the configuration is ther...
Hi,i got a C3560 with IP Base Image. Can i (free of charge) change it to IP Base K9 for SSH support? I did not find upgrade option beetween these two in global price list.kind regardsThorsten
when i try to enter more than one interfacelike the below I get 'invalid number of interfaces specified'mac-address-table static 0000.0000.0000 vlan 10 interface eth1/17 eth1/21 eth1/25
hi,I want to limit traffic on output of my 3750 to the upper limit of my dsl connexion ( 700 Kbps)for making my own qos and not by the provider box,but it appear that it is not possible to make this :Policy Map police_case Class class-default ...
Hi All,I manage a network of Catalyst 3750, 3750E & 6500 series switches and various types of routers. What should I be doing to maintain these network devices in good condition. I monitor the network for faults. I update the IOS periodically. I d...
Hi,I was asked, why one hop doesn't show in the traceroute from Server1. Hop #2 supposed to show 192.168.2.1. Can share with me the explanation?Server1C:\>tracert -d 192.168.6.1Tracing route to 192.168.6.1 over a maximum of 30 hops1 3 ms 1 ms...
How is this possible? Multiple Switches claiming to be spanning tree root.The network has 2 cores. Both 6513. 1 is catos 1 is IOS. Spanning tree seems to be messed up with multiple switches claiming to be root for most of the VLANS here. STP is confi...
Hi,If I put the hub in between the switches (four or five ethernet switches), the spanning tree will not work. The loop would be created. Grateful if you could enlighten me.rdgs
Hi alli have 3750 switch and it is giving message on syslog server it is sending these type of message continusely how can i i can get controle on these type of message%SW_DAI-4-SPECIAL_LOG_ENTRY: 2 Invalid ARP packets%SW_DAI-4-SPECIAL_LOG_ENTRY: 1 I...
Hi folks,I noticed that applications of all of sudden stopped working.Then I connected via console cable and noticed that switch "lost" config.If I do a "dir" I see the following below.Switch#dirDirectory of flash:/ 2 -rwx 269 Jan 01 197...
I have a Cisco 6509E running IOS 12.2(33) SXI3The IOS still allows me to run the following command for creating and Delete VLANSRouter# vlan databaseand after creating VLANs, it should also create VLAN.dat file under sup-bootflash: I have looked eac...
Hello,has anyone ever had an issue where adding a vlan to a core 6509 (VTP server) has caused OSPF adjacencies to flap, the vlan created does not have any host associated to it, it was just created,on the core switch and this appears to have caused a...
