Any idea what this process is? Somehow the CPU util of the switch is now about 50%.What is causing this?36 297064492 5020384 59172 22.29% 24.76% 24.79% 0 VLAN Manager
Any idea what this process is? Somehow the CPU util of the switch is now about 50%.What is causing this?36 297064492 5020384 59172 22.29% 24.76% 24.79% 0 VLAN Manager
Hi all, Im I have a requirement to connect 24+ uplinks to a switch with reasonable performance. I was looking for model in the 3750 series.I dont want to stack switches.Is these any model that can support this?I know the 4500 will definitely do the j...
Hello,We would like to deploy two VSS clusters, one at our main office and the other at a co-location site. We are currently running two HP switches that handle all of the switching between these sites. We have two connections between the two sites...
Hi,Using Avaya phones, each phone requires 15.4Watt of power, so using a 2960 there is no where near enough power for 48 phones, let alone 24. Is there a better model with more POE overall power?Is there a way to boost the power of current models ?...
Hi all,I am planning to install this switch as a 24-port all SFP "core" switch in a relativly small office.I am looking for the following information:1) port-group mapping. When using all twingig convertor modules, which interfaces are connected to t...
Hi, I noticed that on my 2950 switches, sometimes I Configure trunk allowing certain vlans, but then I do show run and the 'switchport trunk allowe vlan x,y' info is not visible. That should come up once ports are enabled on both sides of the trunk, ...
hello,on a cat4500 sup6-e switch with WS-X4648-RJ45V-E card,we have some output drops (giga and so 100M speed's interfaces).the default number of output queue is 40.Can we rise to 50 (or 60) ?is there a commande like the 'hold-queue' one ?I know that...
Dear MisterWhat is the diagnostic that I must to use in a Catalyst 6500 with SUP 720, in order to check the NVRAM function.I get the next message in the console:%Error opening nvram:/startup-config (Invalid Checksum) Is better to open a case???Best R...
After upgraded 4006 IOS, system has a BIG error says "your rommon versio obsolete"... 4006 + supIII ios is cat4000-i5k91s-mz.122-25.EWA14Please where can i download rommon and how to upgrade it...Thanks
Hello,which WAN module with Ethernet port is recomanded for 2650MX to route LAN to the Internet ?With best regardsPavel Kral
Is there a way to disable the stack ports on the 3750FS switch? Thanks.
Hi,We are in the process of upgrading a network of 12 6509's from 12.2.18SXF5 to 12.2.33SXI1. So far we have upgraded 8 nodes, and everything has been running smooth.But - yesterday I upgraded another node and got lots of problems. For example:- I go...
Hellowe are expanding a trunk port over a L2TPV3 tunnel (in port mode):trunk port <-> 2811 <-tunnel-> 2811 <--> trunk portEverything works fine but VTP updates are failing.Sniffer shows that VTP packets are out of order after the tunnel. There a 3 pa...
Hi,Please help me to change the enable password of 3750 switch, I have tried renaming the config.txt, but, every time I rename it a new file gets generated.regards,Navinder.
Hi,we are using 12.2(18)SXE6b on a C6509 with a WS-SUP720-BASE supervisor. A Cisco engineer told us we should upgrade, as the image is deferred.Using the software advisor, I cannot find an IOS compatible with the WS-SUP720-BASE, as it only gives me t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2025 04:41 PM | ||
05-27-2025 03:30 AM | ||
05-27-2025 12:59 AM | ||
05-23-2025 10:30 AM | ||
05-22-2025 08:23 PM |
User | Count |
---|---|
9 | |
8 | |
5 | |
4 | |
3 |