Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
Hi,Bluecoat is used on the network by users to browse internet and its setup asInternet-----ISP---Internet_RTR-----Switch----LANBluecoat is configured on a dedicated VLAN and user on different vlan.Public IP is natted on the Internet-RTR with Bluecoa...
Resolved! Network Architecture Design
I am looking for an article which will walk me through the Systems Development Life Cycle for designing a network. I will be dealing with issues such as selecting routers, switches, WAN protocol, DHCP, DNS, disaster recovery, capaity planning, and in...
Hi,We have a DC (plus DNS) server in our datacenter. This server has two IP's, one for teamed NIC (which is the main production IP), the second IP is for backup network (which enables the storage/backup for teh server data). The production IP is X.Y....
Hi, How do these following logging command differes, when to use one, router(config)#logging host 192.168.0.204router(config)#logging 192.168.0.204Thank you,
Is there a particular brand and/or size USB hard drive that the 2800 series routers will recognize? In the past I have used a 1 to 2 GB USB stick and formatted as FAT. Most of these would be recognized. However, now we are not longer allowed to ut...
Resolved! GBIC and SFP compatibility
I am upgrading the current Cisco 3550 to Cisco 3560. Is WS-G5484 (GBIC)compatible with GLX-SX-MM (SFP).
I have a setup with 3 Windows 2003 servers connected to a Catalyst 3560.The Catalyst has an uplink to an ASA5510.I have an issue with that the servers every now and then cannot communicate with each other.Communication to and from host behing the ASA...
My supervisor blades have 2 10GE ports and 4 GE ports on them. I have 2 supervisor blades on my 4510. I was wondering if I can use all 8 (4 on 1st blade and 4 on the 2nd blade) at the same time. I do not plan on using the 10GE ports.
I'm trying to figure out a problem with regard to EIGRP and static routing and using a route-map policy to inject specific static routes into EIRGP. We have a corporate router and about 24 remote locations connected via frame and a small group connec...
Hi,In our new network setup we have two Router 3600 connected to the two different sites with two links that is S0/1Site A S0/0 ------R1------------------SiteB S0/0---------------R2 --------S0/1for the two site w...
In the PVST world, life seemed simple - Figure out what bridges you want to act as your root and secondary root, set the priorities accordingly, make sure PVST is enabled, set your port to trunk all VLANs, set and enable VTP and away you go. You nev...
I have two 3825 routers that show this for the added cards. Each router has 2 cards.****WIC Slot 0:Unknown WAN daughter cardWIC module not supported/disabled in this slotHardware Revision : 2.0Top Assy. Part Number : 800-27737-02Part Numbe...
Hi All,How can i ping for the particular port on the remote device. Ex: Need to ping PublicIP | port number (tftp) Thank you,
Is the lan interface on this router able to be configured with a non-default subnet mask? ie a mask of 255.255.255.24 Linksys models of comparable costs do not support this on their operating system. I dont want to purchase the router if I cannot su...
Hi.How can I block the communication between two servers on port 8010 on a 4506 switch?. I can do it for access lists?Thanks in advance,R@M
