Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, November 4, 2024 through Friday, November 15, 2024. Our colleagues Rohit Chopra, Vaibhav Aggarwal, Anuraag Majumdar, Saquib Zeya...
Forum Posts
I have a 1601 router running ver 12.0. The ethernet interface is half duplex. Can it be set to full duplex?
What differences there are between the binary config mode and the text config mode?In binary mode, do you need to do a write mem or copy run start? or is not necessary?
Hi Sir,I used Feature Navigator tool to check the features of the following software:Platform : CAT6000-SUP720/MSFC3Major Release : 12.2SXFRelease : 12.2(18)SXF8Feature Set : IP SERVICES SSH LAN ONLY (MODULAR)Image Name : s72033-ipservicesk9-vz.12.2-...
A client just adquiered a 2801 with Adv Security/k9 12.4(12).He needs to use this features: -Web VPN (all context) -Netflow Top Talkers -Application Security LogBut they are not available for that IOS version.Ive just checked in the Cisco Feature ...
This is interesting and it is funny we have never run into this before....I have a 2800 series router with a 4 port Ewic PoE card. I want the 4 ports of the switch to belong to the same vlan as the physical port FE0/0.This seems to be a problem when ...
How HSRP will work with the MULTILINK PPP???in terms of the Interface tracking option...which interface HSRP track if i will have the multiple serial interface belong to the single MULITLINK PPP? Please reply me if possible as this ASK EXPERT event i...
Hi all, I have recieved the setup config from my isp about my internet routers, they say they are load balanced, the config shows that on the fastethernet port that has the public ip on is in 2 groups, its standby for group 1 and active for group 2 o...
Hello, i was wondering if anyone could help with this question. I have a Tranzeo Access Point www.tranzeo.com that will not negotiate with the cisco switch. If i plug the AP into my wireless router's 4 port switch, the AP links and works fine. The fo...
Hello,IS there a way to configure a cisco 6509 switch ports so that if there is a bad switch or NIC card that is chattering and re-transmitting information, the corresponding port should be disabled. Thanks for your help.
Resolved! Convert 6509 from CatOS to CatIOS
Are there any simple directions on how to convert a 6509 from CatOS to CatIOS? SUP720.Thanks.Todd
Hi All,I had faced a strange problem on one of our layer-2 switches.Here is the case:we have four layer-2 vlan switches in operation. all runs with spantree MST.The MST configurations are similarly the same. but unfortionately one of our switches goe...
We're bringing a 10 mb Internet connection into our WAN provider's Data Ctr. A firewall will sit on the Internet edge, of course, but we require a low-port-density layer 3 device to sit on the inside and route to our coporate WAN (static routing is s...
Resolved! VTP propogation issue.
Hello,We currently have two 6509(CatOS) as VTP server with domain name XYZ and rest of the switches (5500) in VTP client mode. So far all the VTP information is being propogated.We recently added a new 6509-E switch (IOS) in the network with the same...
Hi Guys, When starting out, wondered what you guys used as your reference points for things like IOS commands, Protocol Numbers, Timers etc when "in field". Im sure over time I will remember them by heart, but struggling a little right now. I have ne...
6500 with SUP2/MSFC2/PFC2IOS 12.2(18)SXD2 I have an IP subnet of 172.16.0.0/16 on vlan 1 and just configured a vlan 145 interface and bound 172.16.145.0/24 to it. When I did that I get a message that vlan 145 IP overlaps with vlan 1. No problems yet,...
