Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hi,  When I do WS-C2960XR Stack Switch Failover Test,My RDP from thin client to server disconnect.Teaming both thin client side and server side. And log detail below. Any Idea what happing with this switch:Apr 20 10:38:09.985: %STACKMGR-5-SWITCH_READ...

Hi guys, Recently we've added a Catalyst 9500 switch in our production network and i wanted to configure remote access to this switch for monitoring and config purposes.Now, all of our switches are connected to one management switch (Catalyst 2960X) ...

Damon M. by Level 1
  • 5073 Views
  • 5 replies
  • 0 Helpful votes

We are planning to protect line vty (Management plane) for IPV6 traffic in the nexus box .I have already read something about IOS-XE and IOS-XR. IOS-XE ->One ACL for IPv4 and one ACL for IPv6, which cannot share the same name.IOS-XR ->One ACL for IPv...

So my topology is:  DHCP server connected through cable to wireless router that connects to end clients(part of bigger topology). I configured DHCP server to work and wireless router to send IP's to LAN he is in. But I can't find a solution to make a...

SYstemmm by Level 1
  • 3228 Views
  • 5 replies
  • 0 Helpful votes

Hi allI've a core switch composed from two Cisco6509-E with rel.12.2(33)SXH8I need to do a Dual-Active detection modeI can't use the Dual-Active Fast hello because the core's release is too old.So I would like to use the distrubution switches connect...

marzi by Level 1
  • 1717 Views
  • 4 replies
  • 0 Helpful votes

Hi Community, I have 2 WS-C3750G-24TS-1U in the stack. After turning off the Master switch and re-electing master for the second switch I have about 40 seconds downtime before Vlan-interfaces become up. According this documentation I have to have onl...

IGOPAV by Level 1
  • 1117 Views
  • 2 replies
  • 0 Helpful votes

How can i configure a IE 1000 by command line? I find no description about the commands i can use.   Is this not a complete IOS i have on router ?   The command "configure terminal" is not available.   best regards  

Hi everyonei have a WS-C3850-16XS-S  but when i boot the switch it was showing the model number as WS-C3850-12XS-S ,was wondering if these switches are the same ?

Hi, i am looking for the way a sg300/350 timestamps packets such as ptpv1/v2.i know that with ptp aware switches, correctionfield is added by layer 2 with a hardware timestamping, but what is about non ptp aware switches ? is it a hardware timestampi...

I am SO sick of Cisco and their F**king license bulls**t! I've got an ISR4331 and I'm trying to activate the throughput eval license that came with it. The Cisco documentation says:  use the license boot level commandokay....I give..... what is the s...

I'm attempting to set up dot1x authentication on a 3650 switch (just one port for now).  I'm using NPS as my RADIUS server. I'm looking for help figuring out what this Missing Config mentioned in the debug is referring to. The debug on the switch sho...

Running into an issue with a Cisco 3850 in a boot loop after upgrading to IOS XE 16.9.5. Appeared that the switch was starting a boot loader install, received a failed message and is now stuck in the following boot loop: ▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒...