Hi, We are setting up a new site office & as part of requirement 9200 Catalyst switches (4 members) are procured. Just want to know, is there any option to configured this 4 switches in stack without stack cable, as this switches will be placed in d...
Forum Posts
I would like to connect (4) 10Gb SFP+ ports on Catalyst 6880 to Nexus 9300 40Gb QSFP to provide 40Gb bandwidth between 6800 and 9300. Catalyst doesn't have 40Gb port so I am thinking of combining (4) 10Gb SFP+ to Nexus (1) 40Gb QSFP port. I have th...
Hi Is it possible to run Trustsec over a 3rd party VPLS / Telco switching service.Have managed to find options with Macsec for setting authentication to happen in unicast to avoid the transit provider trying to process the eapol messages but cant se...
Hello Colleagues ,I have a cable QSFP-4X10G-AOC10M that i need to connect the 40G port to 3850-48xs and use 2 of the 10G ends , 1x10G to be connected to 3850-24xs and 1X10G to a controller 5520? datasheet stated that These breakout cables connect to ...
Hi all, I'd like to create a macro which changes the port mode to multi-auth and back to multi-domain only if doesn't have a certain interface description. My approach looks like follows: macro auto execute MULTI_AUTH_TEST { if [[ $LINKUP == YES ]]; ...
Hello, We just received our new Cisco 9600 swtiches and I tried to upgarde them the version 17.2.1. I followed the procedure from this Release Note Everything seems to work fine except from point number 5. Step 5 upgrade rom-monitor capsule golden...
My configuration is as follows, indicating the native vlan on each trunk interface:the native vlans are fully tagged across these trunks (except 1003). when I connect the cisco 9300 across the wireless mesh, I get a PVST vlan mismatch error at my rou...
Hello Guys, I have a VLAN with over 200 hosts. I am trying to separate about 6 different hosts from the rest of the hosts in the same VLAN. I want host 1,2,3,4,5 and 6 to be able to communicate with each other but all other hosts from 7 to 200 to NO...
Resolved! Does Catalyst 9300 includes network essential base license once smart licensing is enabled?
Hi, I saw one catalyst 9300 switch the license status like below: smart licensing is enabled, but the device is not registered and eva license for DNA and network adv are already expired. but the switch works as normal. anyone can please help expl...
Resolved! Add another Switch, How to configure?
Hello,I'm new to the community and not much familiar with Cisco-Switches. So far we have a Cisco C3560X switch (SW1) in our network and now we get a new segment, for which a C3560G (SW2) will be used. With the SW1, 4 VLANs are configured, the routing...
Resolved! Need Hardware end of life details
Hi All, I am trying to find Hardware end of life support for Cisco products for below types, is there any way to get that information. WS-C2960S-24TD-LWS-C6509WS-C3560G-48PS-SWS-C4500X-40X-ESWS-CBS3012-IBM-IME-3800X-24FS-MME-3600X-24FS-M ASR1001-XASA...
Hi, This is Cisco 9500 Series switch stack and I am getting alarmed as "%SMART_LIC-3-RESERVE_HA_FAILURE: The license reservation information on the active and standby does not match. Licensing HA will not work properly: Reservation type in active and...
Hi everyone, I am looking for a way to monitor my switch 2960S and 2960X, i need to know if a member from a stack is down. I found a MIB for my product but i can't see the right OID for that... Can someone help me to find th right one ? Many Thanks
please recommend a good python tool with auto compeletion. i.e. if I type 1st letter of the command than i should get auto options of all commands that start with that letter. i.e. if i type "a" then i should get all command options in popup that sta...
Hi team, i'm a newbie in this area. please go easy on me :) . i have some question on how can i achieve my goal to block all connection to specific ip and at the same time allow from specific ip. The scenario that i have is, i'm having a switch confi...
