Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...
Forum Posts
Hi Community Does anyone have a clue how to get SFTP working on configuring Archive feature please? It works perfectly with TFTP but am struggling to get it to work with SFTP. We are using a NAS server that supports SFTP, the server seems to be ok. C...
I have used the SG300 numerous times in layer 3 mode to route between vlans with no problem. This SG350X however is totally new and I can not make it work. Each port can be set individually to layer 2 or 3 instead of the entire switch. Any port set ...
Hi, I have no expertise on the network. I always appreciate your taking the time to answer my question. We will connect independent systems (System A and B) using the L3 Switch (Catalyst 9300).and send the syslog to the cyber security operation cente...
HiI am getting this message:Syslog message generated from device HQ11-COR-11.253: Jan 22 15:46:06 10.255.255.249 1700: .Jan 22 15:45:39:%ENVIRONMENTAL-5-SENSOROK: Temp: Inlet_A, Location: Switch1-R0, State: normalAnyone knows what does that means and...
Resolved! HSRP Multiple tracking
Hello All, As per the below design , if we have 2 core switch , each core connected to a different PE and each has 2 OSPF Adj , Core 1 is the active what i want to accomplish is:- -On Active , Configure IP sla for 10.10.10.1 and 10.10.11.1 and track ...
Resolved! DHCP on L3 switch not working
Hi, Trying to setup a L3 switch with DHCP server running and handing out addresses on all ports.I have a very simple PT file with PC connected to 3650 in GigEth1/0/1, pool configured.Still doesn't work... Please help me find the problem.Attached is t...
I read a lot of documentations regarding HQOS, but not sure how it's programmed on the C9300 ASIC UADP 2.0.I have the following, before changing the configuration a Catalyst 9300 running a HQOS shaper on outbound traffic on uplink.What I've got befor...
Hi AllWe are just looking at configuring our new Cisco 9600 switches, we have noticed that the supervisor card in slot 4 is showing as status provisioned and when I do show redundancy its showing in simplex mode.If I swap the sups around then they bo...
Hi,I've gone through the steps on a 3560 to make a control plane policy. ACLS, Class maps, and policy maps. I would like to apply it to the control plane input but it doesnt seem like the commands are there? Does anyone know the proper way to apply t...
Resolved! Cisco 3750 stack config sync
If you have a pair of 3750 switches in a stack. You then split the stack (not from a config point of view, just say for e.g switch two is powered off) Switch one stays powered on and functioning as the master. If a number of config changes are then m...
Hi, I´m wondering, how to configure this feature correctly? We want to use it as an alternative or as an addition to spanning tree based loop detection. I configured a 2960 like that: errdisable detect cause loopbackerrdisable recovery cause loopbac...
Could you add a non-vPC vlan (a vlan that is not on the vPC Peer Link) successfully to a vPC member port (a vPC portchannel) without the added vlan getting suspended. Please see attached topology diagram. Your advice is much appreciated.
Hello everyone; Iam asking could I configure trunk port between X4500 switch and huawei S5720 switch
ASA site to site vpn with certificate authentication I want to create digital certificate authentication (Can it creates )can anybody route me to the step by step configuration for ikev2 with certificate authentication.
We recently installed some 3850 switches to do Layer 3 routing, moving this off a pair of Nexus 6001s.The plan was to make the 3850 pair the VTP Domain server. But for some reason, it is not possible to create new VLANs on the 3850 pair. When a VLAN ...
