Activity in Technology and Support
UCSM 4.2 (3j) backup failure on the remote host
We have UCSM 4.2(3j), and backups are failing to a remote Linux box.We have the following error codes in the UCSM
Cisco IP Phone 7960 Series
Hello,I was told by Cisco Support that they no longer support the 7960 Series. Our phone system in our office is down and I need support. We already had our phone service provide out and they determined it is not an issue with phone service, rather o...
spa962, rss and cyrillic fonts
At our company we are trying to make a Linksys SPA962 phone use RSS inBulgarian (cyrillic). We installed the latest software (version 6.1.5a) andthe dictionary file bgS_v615.xml, but still all we get on the display isgarbage text. It looks like an en...
Block incoming Calls based off of ANI. (incoming or originating phone number)
The following is an example of how to setup call blocking based off of incoming Caller's ANI. In this example, my voice environment consist of an 8.6 CUCM Pub with 3 Subscribers. I have three Cisco 2911 H.323 voice gateways with 1 PRI in each. I put...
Blocking one Incoming Number in CISCO CME
HiI would like to block incoming call from 1-2 number, i tried creating a rule to reject but not working...extracts of my rules are give below, am I missing something here? voice translation-rule 2rule 1 some old rules.....rule 2 some old rules.....r...
Key Size 1024 weak in version 17.15.3
I have a problem in cisco version 17.15.3 i just installed. It started generating errors : The key size 1024 is a weak key size used in a certificate under trust point CISCO_IDEVID_CMCA_SUDI and will be deprecated. RSA keypair CISCO_IDEVID_CMCA_SUDI...
Expert Insights Series: Empowering Catalyst Center Excellence
Take your understanding of Cisco Catalyst Center to the next level with our upcoming Expert Insights Series! This comprehensive foundational and intermediate series is designed to help you unlock the full potential of your Catalyst Center deploym...
Upgrading firewalls from ASA 5555-X to FPR-1140, AnyConnect client upg
ASA5555-X is going EOL this fall, so we have to upgrade. Looking at running FPR-1140 with ASA to maintain easy migration of 70+ VPN tunnels. Also using AnyConnect 4.9 client currently. I haven't found anything saying i wouldn't continue to be able to...
VLAN issues
I recently replaced the core switch at one of my sites that consisted of two separate C9300-48Ts and three other off brand switches and installed a new stack with a C9300X-48HX, C9300-24S and a C9300-48T (running 17.12.5). This is a layer 2 network c...
Resolved! no switchport command is not working in
I have a WS-C2960X-48TD-L Switch and in this switch routing, routing protocals are working fine even it is L2 Switch. But when I try to enter the command as "no switchport" in the interface mode, it is not working.Actually it is Layer2 switch or Laye...
Catalyst Center Installation Options & Deployment Best Practices
This webinar will take your understanding of Catalyst Center to the next level with this four-session foundational series that's designed to help you Unlock the full potential of your deploymentStay updated on the latest advancementsAdopt best practi...
Looking for Help or a Guide for Writing Basic Config File
Good Afternoon All,Looking for kind of a step by step guide. My org recently purchased 3 9300L switches. Two of them are 24p's and the other is a 48p. I am assuming I can write one file then make small tweaks due to the port capacity. These switches ...
The Value of Telemetry - NX Foundations
This webinar will take your understanding of Catalyst Center to the next level with this four-session foundational series that's designed to help you Unlock the full potential of your deploymentStay updated on the latest advancementsAdopt best pract...
Demonstrating Business Value with Catalyst Center
This webinar will take your understanding of Catalyst Center to the next level with this four-session foundational series that's designed to help you Unlock the full potential of your deploymentStay updated on the latest advancements Adopt best prac...
Blocking a specific number on a sip cube router
Hi everyone I know theres a way of blocking a specific incoming call on a cisco call manager but im not familiar with call manager at all. However I was wondering what the configuration was to block a specific call on the sip cube router instead. Has...
| User | Helpful Count |
|---|---|
| 90 | |
| 79 | |
| 73 | |
| 68 | |
| 65 |
