Technology and Support

CAP3702I-A-K9 can not join to AP3802I-B-K9 mobility express

HelloCAP3702I-A-K9 can not join to AP3802I-B-K9 mobility expressAP3802I-B-K9 mobility express FW version is AIR-AP3800-K9-ME-8-10-196-0CAP3702I-A-K9 FW version is ap3g2-k9w8-tar.153-3.JPQ6a.tarBoth FW version is latest.as the picture, the connection ...

new beta MR 33.1.1

Access points software versions MR 33.1.1 changelog InfoDetailed release notes available at: https://documentation.meraki.com/Wireless/Product_Information/Compatibility_and_Firmware/MR_Firmware_Release_NotesBug fixesGeneral stability, performance, an...

API for Meraki Assurance Alert Profiles

Hi everyone,I'm currently testing the new Meraki Assurance Alert Profiles feature.I would like to automate the creation and management of these profiles (for example enabling/disabling specific Assurance alert types, assigning networks, configuring m...

LACP between ASR and Fortigate

Hello,I have two ASR 920 routers on 17.09.04aI have connected to them via LACP 2x1G optics, two Fortigate 600F and 1800F clusters on 7.4.11the portchannels are connected:service instance 91 ethernetencapsulation untaggedbridge-domain 91and I have los...

Current clients list blank

C1300 24X switches are in stack

Hello team, we have two switches c1300 24X in stack, unit 1 automatically got hanged & all inside subnets are not reachable from outside, Can you please help us in identifying the issue.

Incorrect NDFC intra fabric links

Hi, I am relatively new to NDFC. I have some Palo Alto firewalls that are setup like below. VXLAN SW1 E1/10 <-> Palo Alto E1/1  - Palo Alto E1/2 <-> VXLAN SW2 E1/10VXLAN SW1 E1/11 <-> Palo Alto E1/3  - Palo Alto E1/4 <-> VXLAN SW2 E1/11 When we do th...

Changing port-channel load balance method

Hi,I want to change the current src-mac load balance method in to src-dst-mixed-ip-port or src-dst-ip method on a Cisco 9500-40X switch.I want to know,01.Without changing this on globally can't we change per port-channel?02.Specially want to know doe...

installed Wifi-5 AP mostly RRM auto transmit power at min 7/7 or 8/8

hi,deployed wifi 5 network in an v open area indoor. notice mostly or all of the APs all transmit power at Level 7/7 or 8/8.newer laptop devices with strong wifi AX mostly no issue; but a few older wifi clients like Omron mobile industrial robot alwa...

Support for Transceiver(QSFP) in cisco 8000 (VXR) router

Hi There,We have deployed cisco XR simulator for version 7.10.1 but optics status showing down though we make it "no shutdown" under controller . Could anyone please confirm Transceiver support available in cisco 8000 (VXR) router ?show controllers o...

Assurance-getOrganizationAssuranceDevicesStatusesOverview not accurate

Hi ,Been using getOrganizationAssuranceDevicesStatusesOverview for a couple weeks, I looked at the data and I decided to open a case, after many exchanges with TAC , discovered that this is "expected behavior". This endpoint will only count downtime ...

ATA190 CUCM Locked

I have a ATA190 that is CUCM Locked is there anyway to unlock it

Random Audio Silence During Active PSTN Calls

Looking for some guidance on troubleshooting an intermittent voice issue.The environment consists of Genesys Contact Center integrated with CUCM and a Cisco Voice Gateway connected to the PSTN via an E1 PRI.Users are not experiencing call drops, but ...

Profiler Offline Manual Update - Policies Not Updating

Hello,   How long does it take for an ISE deployment to update the Profiler POLICIES after the Offline Manual Update has been applied?     I have an air-gapped ISE 3.0 deployment and I wanted to update the deployment with MAC OUI and Policies, but in...

Packet capture causing reboot

Hi All Overnight I upgraded my MR to MR 32.2.3 in an effort to resolve a network issue however I have noticed that whenever I run a packet capture it causes the AP to reboot, the affected devices are MR44.So far I'm 3/3 with packets captures causing ...