Activity in Technology and Support
Cisco Packet Tracer Network Scanning
Not sure if this is the right place for this questions but... I work at a place that using the Cisco Packet Tracer software and have been for years until today. We have been banned from updating to the new PT version of 9.0.0 because our security/ ne...
CSCwo09244 - IOSlice temperature sensor shows as failed
The logs are uploaded and let us know the status.
Catalyst EVPN multihoming for non-fabric networks
Are there any configuration guides available for this feature for Catalyst 9300/9300x? We would like to configure and test for an upcoming design.
BPDU Guard
Just a simple question why it's recommended to use both Portfast and BPDU Guard together apart from the very fact that both should be used in access switches ports connecting to end users?? Like BPDU Guard will still work if I don't have portfast con...
Routing to SVI Over Trunk in IOS XE - Can reach hosts but not GW?
Good morning Cisco Community, I feel like i am over looking something simple here. I've built a SVI and propogated it into OSPF on a L3 device. On one interface of that device there is a host connected through two cascaded layer two acces switches....
Need assistance in fixing the uccx script
We have one script that was downloaded from the old UCCX 8.6 system and then uploaded to the new UCCX 15 system. When using this script, I am unable to answer calls from the Finesse desktop, although I can answer the calls from the phone. The other s...
Cisco 2802i AUX Port as LAN Port
Following the instruction from the link below, I converted the AUX port of one of our Cisco 2802i AP's to a LAN port. My hope was to feed a switch from it so I could provide network access to three devices. So far, I can not gain network access. Has ...
Can I ISSU upgrade a C9410R from 17.9.6 to 17.12.6 directly
I have a few C9410R chassis. I want to use issu to upgrade them from 17.9.6 to 17.12.6. If I use the install mode command to upgrade them, will both supervisors upgrade both the IOS and ROMMON statefully?
IE-9320-24T4X-E Port Configuration change
I have multiple setups with these network switches. At least on two different setups, we have connection issues with one of the ports (port #24). We verified that the port configuration has changed and the reminder of the ports configurations remain ...
Set an apply group via netconf on ios-xr
Running this netconf call via ncclient fails to apply the apply-groupdef main(): apply_group = """ <config> <interface-configurations xmlns="http://cisco.com/ns/yang/Cisco-IOS-XR-ifmgr-cfg"> <interface-configuration> ...
IOS-XE Ignore Radius VSA's
I was curious if on the Cat 9k series switches, is there a way on a port (or many whether individually or globally) to have the port ignore any VSA attributes sent back by the radius server. Like if I want to ignore the VLAN or the IBNS template tha...
Failed to send Certificate Auth request to rest ID store: Azure_EntraI
I am currently working on device-based authentication and authorization against Microsoft Entra ID–joined devices using Cisco ISE 3.4 Patch 4.I followed the official Cisco documentation to configure the REST ID Store integration with Entra ID (includ...
Entra Joined Device and AD User with TEAP(EAP-TLS) and EAP Chaining
Hello Greg, @Greg Gibbs Refer to your KB https://community.cisco.com/t5/security-knowledge-base/cisco-ise-with-microsoft-active-directory-entra-id-and-intune/ta-p/4763635#toc-hId-2135119435 and section - "Entra Joined Device and AD User with TEAP(E...
Cisco ATA 191 - CUCM/Registration
Hi There, Looking for some advice/help. Our service are in the process of gradually moving to IP telephony. Some of the sites have the requirement to be able to use there current analogue phones. I am trying to set-up a CIsco ATA 191 but not sure wh...
Cisco ISR router as a modem in bridge mode
Hi GuysIs it possible to setup a Cisco ISR router as a modem, so I can bridge the ISP to my Meraki FW behind it, It will connect to BT internet using pppoe, I want to pass the traffic coming in from the ethernet 0 interface to the LAN port fast ether...
| User | Helpful Count |
|---|---|
| 65 | |
| 55 | |
| 41 | |
| 35 | |
| 32 |
