TelePresence and Video Infrastructure

VCS and CUCM integration

hi, VCS: - I setup a neighbor zone to CUCM, with no transformations, and a search rule that points all calls to that zone. - I also disabled H323, and am only working with SIP - I have successfully ran SIP Video calls between all endpoints registere...

Resolved! ADD EX90 TO CM (sip)

We are running UCM 8.6.1.2006 EX90 TC7.3.0 Unable to get the EX90 to register with the CM ??? Error on the EndPoint is provisioning - HTTP -404 Any help is appreciated ... Verified Provisioning connectivity is Auto httpmethod is GET Home SIP Status ...

got lot of unknown call logs

hello all experts,I am getting lot of abnormal call logs in the VCS expressway, I am afraid we are suffering an attempting to make illegal call via our VCS expressway, could you please kindly help me to look at the attached logs,thanks in advance.Yu.

Resolved! Telepresence Content Server

I've been reviewing some information on the telepresence content server and figured someone here might know the answer. I am reading some conflicting information. Can the telepresence content server be used to watch a live stream?Can the telepresen...

Resolved! C60 DVI Output not working with Casio Projector

C60 DVI output to Casio projector HDMI input signal fails.Can anyone help to fix the issue.SW: 7.1.4

MX300 and MX200 standalone

Hi there,I want to make a demo with one MX300 G2 and MX200 G2 for a customer.I want to use both endpoints in a standalone mode, the customer doesn't have any vcs or cucm. ( Point to point call);I read in the following thread that i must use H323 to b...

Scheduling a non-room based video meeting in Outlook - No Webex!

Are there any 3rd party apps or apps that allow a user to schedule a Telepresense meeting were a room is not being used? In this instance we are up against Skype4B and the standard is using Outlook to schedule the meeting that the Skype client then ...

Resolved! MCU 8510

Hai, i have a MCU 8510 in one location which have a 40 port open and i have an another MCU 8510 located in another place with 40 port open, both are in the same network. My requirement is can i make a 80 party call by merging or clustering this both ...

Resolved! Telepresence Server - change a language voice prompts

Hi expert, I have a CUCM 10.5 + Conductor XC4.0 + Telepresence Server 4.1(2.29), and I need to change a voice prompts from english to french, Can you help me ?

Resolved! Hybrid Services and Connector Management on VCS - Cloud Collaboration Management - Features and Workflow

Hello community, I have a few questions about the Hybrid Service on VCS: - We just have one VCSE on WAN. How can we deploy Hybrid? Or we have to buy a VCS? Is eval vm eunogh ? - What are the Features with just VCS? Are we able to connect TeleWorker...

CUCM-VCS Integration VCS B2BUA Encryption Call Failures

All,I have the following scenario: CUCM 9.1.2SU1VCS X8.1.1MX300 endpoints (CUCM registered) We are not running in mixed mode on CUCM We want media streams with external call parties to be encrypted. We do have TLS end-to-end but I don't believe we ca...

TMS migration(upgrading and changing server)

Hi all,We plan to migrate TMS 12.6.2 on Server 2003 R2 SP2 with SQL 2005 Express to TMS 13.2.2 on Windows Server 2008 R2 64bit with SQL 2008 Express.Server name(host name) and IP adrress are not same as old server's.Are these procedures in Bold are c...

Resolved! Tandberg vcs and Cisco VCS Control

Hi, I have a customer with an old video infrastructre and new servers. Old Video Servers Tandberg Video Communication Server Control Appliance - Part Number = 117500 Tandberg Video Communication Server Expressway Application - Part Number = 1163402 ...

Content tx: bit rate mismatch on calls on the 8510

Good Morning One of my clients us currently having issues sharing content with on particular endpoint when in an MCU call. The endpoint is an MX300 which I beleive comes loaded with all they keys required to view presentations. I can confirm that co...

Resolved! Cisco IX5000 supports H.323

Hi all. I have a question that Cisco IX5000 supports H.323 protocol. There is only SIP in the datasheet I checked. But, my customer don't want to buy CUCM. They only want to call point-to-point between 2 IX5000. Thanks.

TelePresence and Video Infrastructure

Forum Posts

VCS and CUCM integration

Resolved! ADD EX90 TO CM (sip)

got lot of unknown call logs

Resolved! Telepresence Content Server

Resolved! C60 DVI Output not working with Casio Projector

MX300 and MX200 standalone

Scheduling a non-room based video meeting in Outlook - No Webex!

Resolved! MCU 8510

Resolved! Telepresence Server - change a language voice prompts

Resolved! Hybrid Services and Connector Management on VCS - Cloud Collaboration Management - Features and Workflow

CUCM-VCS Integration VCS B2BUA Encryption Call Failures

TMS migration(upgrading and changing server)

Resolved! Tandberg vcs and Cisco VCS Control

Content tx: bit rate mismatch on calls on the 8510

Resolved! Cisco IX5000 supports H.323

Congratulations to the Event Top Contributors Class of 2024!

Cisco + Splunk: It's a new day for your data.

A new chapter of the Spotlight Award begins!

Join us in Celebrating the New Year and the Nov.-Jan. Winners!

Announcing Resources That Guide You to Success

Can not add join link in Cisco Meeting Server Email Template

Room Navigator Meeting Title display: 0365 Calendar with Control Hub

USB Passthrough mode in Microsoft Teams Mode

Dialing Commands in Microsoft Teams Mode

Call statistics not showing in Control Hub

Configuring Cisco mx 700 via web interface

Firmware for CISCO WEBEX systems

Can I disable / hide "New Number" in Jabber for call forwarding?

USB to RS232 AV control: works in command line, not working in a Macro

Factory reset exisiting registered Webex room kit.