Hi,Has anyone come across the alarm with their VCS Control? If so could you explain what would be causing the error and how to resolve the issue?VCS version x8.2.2 Thanks
Hi,Has anyone come across the alarm with their VCS Control? If so could you explain what would be causing the error and how to resolve the issue?VCS version x8.2.2 Thanks
Dears,I am new to TCS and VCS, i want to implement TCS which will receive stream from TP endpoint and it will push to appspace and then to DMP,I am actually confuse in how many different scenarios we can use VCS, and which are the different device t...
hi, GUYS meet trouble that the configuration of Auto Answer on the Video endpoint like EX90 or SX20 would be lost after i restart them , i confirmed that i had saved the configuration, but i still will be lost just after the device restarted ...
Is it possible to configure Content Server for using external NAS and DB without put Content Server in a MS Domain?
We can make calls back and forth using a Cisco 9971 that is registered to the CUCM to VTC codec that are registered to a VCS. But when we try the same thing with the SX10, the call begins to connect but then drops. Logs on the VCS just show the cal...
VCS Control Running 8.1Codian 5320 MCU running 4.4(3.42)CUCM running 9.1 EX90 running TC5.1.5.297625 SX20 TC6.2.0.20b1616EX90 & SX20 > Registered to VCS8945 > Registered to CUCMMCU is registered with CUCM and VCS both.When i initiate a multiway cal...
We recently purchased 4 x LIC-VVCS-E-M-PAK and 4 x LIC-VVCS-C-M-PAK so we could migrate all our call licensing from VCS HW appliances to VMs, however when I go to redeem one of the PAKs I got for the VCS-C, it's only showing the following as availabl...
Hello,I installed TMS 13.2.1 without release keys. when entering the main page the serial number appears as TRIAL.I request DEMO release keys to a Cisco representative for my lab.He generated a release key but for another serial number, and told me t...
Hi Guys,we are experiencing a problem with inbound calls on a ISDN LINK paired with a sx20 telepresence codec.Release software used are: SX20: TC 7.2.1ISDNLINK: IL 1.1.4ISDN connectivity is provided by an E1 PRI channel.Description of the problem:Inb...
Hi there,I want to make a demo with one MX300 G2 and MX200 G2 for a customer.I want to use both endpoints in a standalone mode, the customer doesn't have any vcs or cucm. ( Point to point call);I read in the following thread that i must use H323 to b...
Good EveningI using the internal address book of SX20.I know how to remove and how to add data to the address book.(I use the API command)However, after I have deleted the data that has been registered in the address book, number will continue to be ...
Hi all, We're planning to check the status of SX10 by using its API, but unfortunately we don't have any SX10 yet.Does anybody know if the parameter below works fine on SX20 TC7.2?(I guess "Multisite" will not be used, because SX10 has no Multisite ...
Dear All,I have an authentication fail issue during endpoint sip registration to VCSC.VCSC event log say that user not found. But user was created in VCSC local database and that user credential is working for h323 authentication. On endpoint system ...
Where can I find the API for a cisco CTS-CODEC-PRI-G2R (Tx9000)
I've come into a new environment with my new job and noticed that the TMS server has TMSPE installed, but when going to TMS general settings, I don't see the right dropdown. I only get Enable Cisco TMS Agents. I am on TMS 13.2 (looking to upgrade to ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-11-2025 04:15 AM | ||
06-06-2025 12:26 AM | ||
06-02-2025 07:45 AM | ||
05-23-2025 07:20 PM | ||
05-19-2025 05:53 AM |
User | Count |
---|---|
2 | |
1 | |
1 |