Hi, I am just wondering what the effects are of UCS Central license expiration. If a trial expires, does the UCS domains and service profiles become unusable (causing an outage), or do the profiles and configurations stay, but changes are not allowe...
Forum Posts
Resolved! Issues Facing after using Inband IP KVM
Hello Gurus, I am facing an unusual behavior in UCSM 4.0 (2b) while using inband KVM access. Everything working fine, Service Profiles are getting IP from Inband Pool. Accessible and KVM launch is also working. IP Pool Size is of 16 IPs and 3 are use...
Resolved! UCSM & Blade Firmware
I am planning on running an Infra firmware upgrade on my current UCS domain. It's currently 3.2(1b) and we are planning the upgrade to 4.0(4e) so we can make use of some new M5 blades. The M5 blades are going to replace the existing M3 and M4 blades ...
Hello,What is the best practice or Cisco recommendation regarding automatic (or manual) Windows updates for Hyper-V running on HyperFlex? Should I update Windows every time new update appears or it's better to avoid them? I have seen some recommendat...
Currently we have our fabric interconnect communicating to tegile storage via Nexus 6k and unfortunately as one vlan on a trunk. I want to separate the traffic and I could create port channels to the nexus 6ks with only the storage vlan traffic. Woul...
Resolved! HX native snapshots
Hi I have a cluster of HX220c M5 nodes and would like to know a bit more about how native snapshots are created and stored. I have read the HX Data Platform Admin guide that explains how to create native snapshots manually or using a schedule, with ...
I'm trying to run ucscfg(v3.0(3)) on my video-less C220 M4 so I can try to get control of it through the CIMC.I'm getting...---./ucscfg show text /biosUCS Configuration Utility v3.0(3)(c) 2017 Copyright Cisco Systems Inc., All rights reserved.Error :...
Resolved! UCS Netflow Exporter Best Practice
I was trying to setup netflow in UCS but ran into some questions. When creating the exporter interface, what is a reasonable VLAN to choose? Would it be good to use the management VLAN of the UCS management - in the same subnet as the Fabric intercon...
Hi,I'm asked to reset and migrate an old UCS B200 M4 blade server that was administered by a resigned sys admin. All OS and data in this server is not used anymore. When I raised a support ticket to cisco they mentioned the CIMC but I cant see it in ...
I am a student, and at our school we have a cisco ucs c220 m3 server. I want to install that server with CentOS. I usually run Centos and other OS on VirtualBox and VMware. so I am new to this assignment. can you provide other documentation / videos ...
Is there a way to disable SecureBoot Support on C220 M5?Need to install ESXi 6.5 and I'm getting an error "Invalid Signature detected. Check Secure Boot Policy in Setup"
Hello, during the installation of the Hyperflex cluster I had created iSCSI interfaces for this kind of traffic.But I am dealing with these errors now. host-eth-10 and vif-1298 are tides to the iSCSI interface.How can I shut down or disable this prep...
Hi all,We are deploying cisco hyperflex edge cluster of 2-node.After providing all the required details in the hx installer wizard, when we start the validation process, there is an error in the deployment validation stage. It says "Errno 113 no rout...
I have a Cisco HyperFlex with 9 TB of disk space. I created 10 VMs and had those VMs running for about a week, after that, I deleted all the VMs(Delete from Disk) on the vSphere web client, but I am not able to get my space back and it disappeared. l...
When executing the command ucse sub 1/0 status, does not report any information. The blade is working fine otherwise, statistics works through the isr 4351. ISR4k#show version | inc RELCisco IOS Software [Fuji], ISR Software (X86_64_LINUX_IOSD-UNIV...
