Hi ,We have UCS 210 M2 with CIMC 1.4.2. We are getting the Lower Fatal Error for 2 fans & RPM are shown as 0. I couldn't find anything with UCS fault Message reference guide.Thanks in Advance.
Hi ,We have UCS 210 M2 with CIMC 1.4.2. We are getting the Lower Fatal Error for 2 fans & RPM are shown as 0. I couldn't find anything with UCS fault Message reference guide.Thanks in Advance.
I will be replacing a 6120 with a 6296 in the near future. I have the Upgrading Cisco UCS B-Series Hardware pdf which gives an overview of the process for replacing a 6120 with a 6248. The 6120 we have has the 6 port 8Gb fiber channel expansion mod...
Hi Cisco Top Guns!!!I have tried to migrate some service profiles between servers M2 (with M81KR) to M3 (with Vic 1240 and Vic 1280) and Windows 2008 R2 recognized the interfaces on M3 as new interfaces. The ghost devices interfaces (old interfaces) ...
Hi,I need help to configure my Cisco UCS 6248 + Cisco Nexus 5548 + EMC VNX 5500, I have a following connectivity in placeFI-6248-A to N5K-A - 4xFCoEFI-6248-A to N5K-B - 4xFCoEFI-6248-B to N5K-A - 4xFCoEFI-6248-B to N5K-B - 4xFCoEVNX SPA-P1 - N5K-A-1/...
I am using Citrix XenServer for a hypervisor. I have 4 main vNIC assigned in the server profile. vNIC 0 is what I use for the hypervisor NIC, and the policy I set on this vNIC in the UCS is a Linux profile. But I am noticing that the vNIC's that I am...
Hi,I installed ESXi 5.1.0 on UCS B230 M2 Blade, after IP address Configuration then appears the below:"Download tools to manage this host fromhttp://192.168.60.101/ (static)" But i can't ping this IP Address and I can't reach it by http.I use the sam...
Hi All,I am getting so confused here and any help will be much appreciated. Last night I was able to ping my VM-2 machine successfully (192.168.60.102) which resides in blade 2 of chassis 1 but unable to ping the VM-1 Machine (192.168.60.101) in blad...
Can the Nexus 55xx with Unified Ports be deployed as strictly an FC switch WITHOUT FCoE? For example, take an HBA and connect it directly to a UP port configured as an FC port and use the switch as such - no FCoE.
I am having an issue installing ESX to san boot lun, it times out saying lun not found. The adpater is 40G mLOMs running version 2.0(4b)Same connectivity (VSAN, zoning) works just fine for a 200 M3 with Palo adapter on it.Any known...
We're in the process of replacing our UPS unit inside one of our data centers whicih currently houses one of our UCS's, everything needs to be shutdown in there, so I was wondering what's process for properly shutting down the UCS. We have the follow...
Hi all,i've configured this topology for Ethernet and FCoE uplink from 6248UP to 5548UP:When i check flogi database from n5k the result is:n5kA --> no vfc to 6248A was loggedn5kB --> vfc to 6248B is up and runningThis is sh int vfc21 (n5kA FCoE Po to...
With Robert BurnsWelcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about Cisco's line of VICs adapters for the Unified Computing System (UCS) B and C Series with Cisco expert Robert ...
Hi,Is CDP is enabled by default in UCS? If not then how we will enable it? While enabling the same in production setup will cause any impact on Network link or production? Anandraj
after i migrated a vm to n1kv. the vms cannot get access to the network. I did a show inte vethernet 109 status and status is up. vlan is correct. other vms on this vlan works just fine. duplex/speed is auto autoany idea?thanks
I'm having issues with the VXC 2111 not displaying to the 2nd video input. The 2111 is attached to a 9971 directly to two Dell monitors using DVI cables. The 2111 is running the latest firmware. Any thoughts?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-30-2025 01:15 AM | ||
04-21-2025 05:41 AM | ||
04-11-2025 01:36 AM | ||
02-23-2025 12:10 AM | ||
02-21-2025 05:23 AM |