Does anybody made experience with the new B200 M3 Blades and XenServer? does this run? also with VIC 1240?Thanks for inputsManuel
Does anybody made experience with the new B200 M3 Blades and XenServer? does this run? also with VIC 1240?Thanks for inputsManuel
We purchased UCS (2 6120XP fabric interconnects and 2 5108 chassis with blades) a couple of years ago. We are just getting to the point of needing to add an additional chassis. I'm presuming adding the additional chassis is pretty straight forward....
I work for a major Cisco distributor, and we have a two chassis UCS system setup for demonstration purposes. One of the blades is a B440 M1, and the RAID BBU (battery backup unit) is missing. We don't have another one to replace it with, and since th...
I am having some problems with VMWare connectivity to Netapp storage via the Cisco UCS. Have found no errors at any ethernet interface and no errors on the Netapp side. One thing I would like to eliminate is the possiblity of QoS shooting us in the...
What is the recommended cabling and cable type for wiring up between a 5108 chassis and 6248?
Hi,I have the following setup-NetApp Storage-2 x UCS C200-M2-Qlogic HBA 4Gbps dual port "QLE2462"-2 x mds 9124 running 5.0(1a)The NetApp is stable and and apparently no problems, but one port of each HBA area constantly loosing connectivity, I'm also...
Hi, I hope someone can helpWe have 2 separate UCS installations, identical hardware config; 2, FI's, NetApp direct-attached storage, and upstream HP switches. I have one installation up and running, iSCSI boot working fine.The other ins...
hi GuysI have upgraded my VC to 5.1 and am using nexus 4.2(1)SV1(5.1a)When i go to register the plug in i get the message below , all hosts are 4.1.0 specified parameter was not correct, extension.keyCall "ExtensionManager.RegisterExtension" for obj...
The release notes for 2.0.3 indicate to use UCS Manager Capability Catalog version ucs-catalog.2.0.3d.T.bin.the latest one that I can find is ucs-catalog.2.0.2g.T.bin from http://www.cisco.com/cisco/software/release.html?mdfid=283612660&flowid=22121&...
Hello,In UCS Manager one can monitor the %BW of certain interfaces like the physical interfaces of the Fabric Interconnects. That's ok but is not very useful in my opinion because they're just instantaneous figures...you do NOT get any AVERAGE %BW st...
Hi:I am still puzzled by the following. It is related to the other question I posted, but there seems to be no answer from anyone, Cisco follks in particular.q1.If I have B250-M1 and it comes with 2 Adapter Slots, BUT if I just INSTALLED a single M81...
Hi, Cisco Folks:Can someone please help me to clarify the following doubts?Q1. What is the pinning order of B250-M1 to IOM if I have 2 Server Ports with a fully populated chassis of 4 B250-M1?I know that for a half-width, the pinning order will look...
Hi Guys,We are two versions of UCS manager 2.0(1w) and 2.0(2m) .I have the latest version of Java in my laptop but it gives me to diffrent error messages when I try to laucnh the UCS manager.I tried uninstalling and reinstalling did not help.dleted ...
I am looking to design a solution for a customer and they run a very tight hosting environment with Nexus 1000V switches and want to setup private vlans as they are running out of vlansI need to find some info on if it is possible to trunk a private ...
Can anyone confirm whether VM-FEX / distributed vSwitch is supported on UCS B200 M2/3 running under vSphere 5.0 U1 (build 702118 or 623860)? I am getting mixed information. My local Cisco SE told me Cisco had revoked support for U1 until a new driv...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-01-2024 11:45 AM | ||
06-26-2024 10:37 AM | ||
06-20-2024 06:10 AM | ||
06-14-2024 01:49 PM | ||
06-13-2024 07:31 AM |