Voice over IP

HelloI have a scanerio where I need some help. I got my VoIP Network setup and it is working. I would like to add a new service to provide IVR serviceCurrently my IVR is working as followNetwork Diagram:PSTN ---> c3640gw ----> Internetdial-peer voi...

We upgraded to Callmanager 3.3 a few months ago and just now our users mentioned that the ATA 186's that we have are not working. They were configured as 7960 devices but now are automatically made into ATA devices in CM. I set the line number on 1...

23F4 : 339132627hs.783352 +-1 +1303 pid:2 Answer 62844795 dur 00:00:00 tx:119/2361 rx:610/12200 10 (normal call clearing.) Telephony 1:D:783358: tx:7990/799/0ms g729r8 noise:0dBm acom:0dBm23F4 : 339132627hs.783353 +-1 +1340 pid:964 Originate 1927656...

When I connect FXO i Cisco 2611XM (12.3) to PSTN and used "supervisory disconnect anytone" is impossible to make the call from FXS to PSTN. Why?Any body know?I need this command because this solve problem with no call disconnection when call goes fro...

Hi allplease i need to know, when applying IVR system on MY AS5350 are those script included in the IOS need editing or i can use them as is without adding anything?how can this script know how much money remainig in the account in order to play the ...

I need help with a design issue. I work with call manager and small voip gateways and this is the first time I have worked on a 5350.I have a Sonexis conf device with a pri in it going out to the PSTN I want to direct connect it off of the 5350 so IP...

hiIf i have a gatekeeper and a gateway router at Site A and in the event of a failure of the PBX or the gateway router want to route traffic hitting the gatekeeper to another gatekeeper and accordingly to the PBX at site B. What do i setup in the gat...

Hello ya know, i've been watching calls on my frame now for some time.. Now, I notice how the noise output jumps around alot.. if I do a sho call active voice brief, what does that noise=? mean?? If the noise is -64 or positive 64, I don't know ...

Anyone have any ideas regarding a Route Pattern which is failing to the NEXT Route List available? I am running CCM 3.2(2c). The Route Pattern looks like 1865.XXXXXXX and fails to the Route List specified. The call completes to the next route list...

Dear All,I am using a Cisco 3640 (IOS ver 12.2(21T))as a VoIP Gateway.There was no isues until I only had H323 on the Gateway.Now,I also want SIP as well to run of the same Gateway.Thus,H323 and SIP has to work on the same Gateway at the same Time.Th...

Dear NetPros,I want to connect the E1 coming out of an Alcatel 1000 S12 Switch into the Cisco AS5350. The Alcatel Switch has SS7 and V5.2 as the standard interfaces. The E1 is a Tx and Rx pair with BNC type terminators. Can anyone suggest me how I ca...

Dear allcan anyone explain to me this command and what is used for?i tried some of the white papers but didnt clarify ittks

hiI have a PRI from a 7206 to a Definity G3R. Doing a show isdn status and a debug isdn q921 shows and confirms the PRI being up. However when i dial the remote i don't see the call hit the 7206. What are some of the debug commands i can use to ve...

Hi,I have some IP Phone 12 SP+ configure with Cisco Callmanager the version 3.3 2 Sp (B). My Problem it presents as the following: The IP Phone (12 SP+) receives a call, when the user pick up a phone to answer the only thing which he can hear it’s a ...

We have a setup of a central 2610 Router acting as Gatekeeper and remote 805 Routers.The setup is working fine but the problem is when a conversation is going on if another person calls up he is not getting the busy tone but he also gets the ring ton...