Voice Systems and Accessories - Small Business

Hi,I hope, someone can help me:I have installed a UC320w, use 1 Sip-Client and calling in and out is no problem, but I cannot manage to disable, that outgoing calls send the CLID Extension with them; I have tried to manage it with the inbound rules, ...

Dear sir,I have a problem with a phone spa 303 firmware 5.0.2 connected to an asterisk server.When I make a call using an isdn card, and the other end hang up before answering, the phone continue ringing (seem don't detect other end hangup).I tried t...

We have this downloaded (V 2.2) - was told it's free.I assume the SERVER IP it's looking for is either Cisco UC540 or CUE and the username/password is the mailbox user's username/password. That doesn't work. So... 1. Is there an install guide? Nothin...

Hello All,I have an installation with a SPA400+SPA9000 and phones 3x SPA942 and 1 x SPA921. Country is Czech Republic.Incoming  calls shows "Anonymous" instead of showing the caller id. I follow some  instructions, I have seen, in a documentation tha...

Hi, I`m new to cisco products.I`m in the process of connecting a phone in a remote office to the uc520 in the main office thru a IPSEC VPN tunnel established between two fortigate firewall, I tried for a long period and can`t get that phone connected...

Hi all,I made an Auto Attendant on a UC500.This workx fine, only one problemWhen a customer press 2 for service the phone rings on extention 23.But when 23 is forwarded to an external number it doesn't work.So I forward 23 to 006xxxxxxxxxx then it do...

Hello! I am in great need of help. I bought a used Cisco 303 phone to use with Ring Central. However, when I went to provision the phone on the Ring Central interface, the IP address read 0.0.0.0. How do I get the IP address? I am a small business ow...

I am having trouble getting the SPA112 to recognize DTMF tones from my phone in AVT mode. Using InBand mode DTMF works for the most part, but there are some IVRs that don't seem to like the audio DTMF either. Currently my phone plays DTMF tones for 8...

I have had some issues with phones restarting themselves on a UC560 (8.6.1). Firmware updating the SPA handsets helped alot and I have a single 7962 receptionist phone left to do. It has firmware 9.1.1. The 8.6.2 software pack shows this same version...

I got a new SPA112 and connected it to FreeVioPDeal account ( http://www.freevoipdeal.com/ ).Used Quick setup wizard.After that everything looks fine (I can call numbers in US and Israel, people can call me etc.) BUT I can't call other VIOP users usi...

Hi,Is it possible to configure UC560 and UC540s kept in different locations as Publisher and Subscribers and there by avail the centralised deployment advandages?I have one client with one UC560 at Head office and two UC540s at two different branch o...

Hello Everyone, Have recently taken over a UC560. We are having an issue were we can not get to the auto attendant. In our case its 3000. Not sure if this is part of the same issue but we cant dial the voicemail system either 3999.  Any help or where...

So staring in 2014 an SMB who wants a Cisco UC Voice solution (Phone Systems specifically)  must spend about 10K list for the system plus phones and a switch minimum for up to 25 phones....At those prices Cisco is effectively pricing themselves out o...

I have a UC320W with 5 phones and 4 lines.  HOw can I add more PSTN without using sip trunk?  Thanks

Hi,I just bought a new SPA509G phone. I updated to the newest software (7.5.5) and I have it configurated the phone to work with our "local" Asterisk system.Requirement however is to work with some external sip accounts also, like my bosses home. We ...