Buy or Renew
Buy or Renew
Duo Security forums now LIVE! Get answers to all your Duo Security questions. Learn more

VPN

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Cisco CyberSecurity
Labels

Forum Posts

Start a conversation

Resolved! Wierd NAT behaviour with AnyConnect clients

Hi there,I have a problem with our AnyConnect clients not being able to access a particular resource that exists on a 3rd party VPN network.Both AnyConnect clients & 3rd Party Site to Site VPN terminate on the Outside Interface of the ASA.There is a ...

Error 442 in Windows 8

Hey guys, hoping you can help. First off I ran through and was going to do the registry trick as the video's and other discussions suggest.  I went through the steps only to find that it was aleady correct in the registry.So I keep getting that same ...

routing issue on ASA5505 site-to-site VPN

Dear All:I have Cisco ASA5505 on both office. And it has connected fine for a few month. Today, user report no connection in between. After discover the VPN, I found the VPN session on both site still established. However, Site B (remote site) cannot...

who by • Level 1
  • 475 Views
  • 2 replies
  • 0 Helpful votes

Resolved! ASA 5505 IPSEC VPN connected but can't access to LAN

ASA : 8.2.5ASDM: 6.4.5LAN: 10.1.0.0/22VPN Pool: 172.16.10.0/24Hi, we purcahsed a new ASA 5505 and try to setup IPSEC VPN via ASDM; i just simply run the Wizards, setup vpnpool, split tunnelling,etc.I can connect to the ASA by using cisco VPN client a...

sai cheng by • Level 1
  • 5139 Views
  • 6 replies
  • 0 Helpful votes

Remote Access VPN - split tunnel configuration

Hi:I have a need to setup split tunneling where by 99.9% of the traffic needs to go through the tunnel and the other 0.1% can not. Therefore I created a group policy and under Advanced -> Split Tunneling I set          Policy: Exclude Network List Be...

Aditional routes in split tunneling

Hello,we are using  a c1841 with IOS version c1841-advsecurityk9-mz.124-15.T.bin. As remote software we use VPN client version 5.0.07.0410.My configuration is:  crypto isakmp policy 3 encr aes 256 authentication pre-share group 2!crypto isakmp client...

Resolved! Two links one for Site-to-Site VPN and other for internet on same router configuration

Hi All,I have 2 internet links one ADSL and one leased terminated on the same router. I need to configure ADSL for site to site VPN to HO ,and leased line for dedicated internet for all users.my site IP subnet is 10.10.100.0/24 and HO subnet is 10.1....

Resolved! VPN PROJECT - CISCO ASA

Hi All,We have a large project ongoing in which we are setting up a firewall / VPN service to offer customers VPN connections back to a single VPN server. We will have around 1,000 users but only run about 200 - 250 concurrent sessions at any one tim...

veltech by • Level 1
  • 499 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Modifying Existing VPN on ASA version 7.1

Hello All,I have two issues to resolveI added 5 new network ranges to an existing B2B tunnel. Three (3) of the new network ranges are able to establish sessions over the tunnel but two (2) are unable. I did a tracert from computer and the trace termi...

Folders/Files Disappear? Only on VPN?

Hi Everyone, have a very strange issue.  When one of our few hundred clients on VPN uses a shared network resource through the VPN... either by mapping a network drive or browsing to \\x.x.x.x (Server IP), they can open the primary share and see the ...

ASA for incoming Remote Access VPN

Hi All,I'm looking to configure our ASA 5501 for incoming VPN clients.My query is, the current Interfaces on the ASA are as follows..I want to assign any VPN clients an address on the 10.x.x.x network. Do I need an ASA interface on this network also?...

GRANT3779 by • Spotlight
  • 731 Views
  • 12 replies
  • 0 Helpful votes
View All