dear all,As of now I am using Microsoft VPN tunneling to access Microsoft Outlook application. (same as I am in My Office). can any one show it is possible with SSL Technology.regards,ZAK
dear all,As of now I am using Microsoft VPN tunneling to access Microsoft Outlook application. (same as I am in My Office). can any one show it is possible with SSL Technology.regards,ZAK
If I want to limit what an l2l connection can get to do I create a group policy and specify it under the tunnel general attr for the site to site and define the filter in the group policy? thx
Hi,I have the following setup : TACACS --- LAN --- ASA1 ==== IPSec === ASA2 --- SW1 In my configuration, I can manage the remote ASA (ASA2) on its inside interface, through the IPSec tunnel with SSH. For that, I ente...
Hi,Here is the scenario:I have tunnels to HO from all BO(Hub and spoke)A-- HQB- BOC--B0A-B tunnel down, A-C tunnl up,B-C tunnel up.Now I want to send the traffic B-C-A thru VPN tunnel is it possible.I dont hve a time give the brief info. pl. do the n...
Hi, we're trying to create a 2048 request for an EV SSL cert from our concentrator 3000, running 4.7.2.L. When the cert is created however, it only creates a 2047 bit request. We need a 2048 however, as it is to span 2 years, and 2048 is due to bec...
Hi All,I have a c2511 which I use to access my lab. It connects back to the LAN on the AUI port with a standard CentreCOM 210TS 10Base T transceiver/connector.It works for a while and then stops.At first I thought it was a faulty connector or a probl...
We have two ASA at different locations. These were bought with same licensing, but when checked, they show different capabilities for WebVPN Peer support:ASA-1 using asa804-23-k8.bin:> WebVPN Peers : 2 ASA-2 using asa803-k8.bin:> WebVPN Peers ...
I have an hub and spoke configuration.ASA5520 is the hub, zyxel are spokes.Due to limitation on zyxel, I can only setup a single line remote network/local network.the two branches must talk each other, and with a server on central site.I wanted to pe...
Hi,is it possible to use SSL-VPN (anyconnect) on a Cisco2811 (client -> router) and then using NAT to translate the IP of the client for connecting to the network behind the router?The problem I see is there is no interface to use "ip nat inside" on ...
Hi,Howmany vpn group is supported on asa 5520 with remote access vpn configuraion.Regards
I have ASA5510 behind NAT-router,so outside interface has private IP. For VPN I am using ipsec-over-udp and ipsec-over-tcp. When I am connecting via ipsec-over-udp everything is working fine, but when I am connecting via ipsec-over-tcp connection is ...
i have a situation here. We have a LAN-2-LAN tunnel established. My end is an ASA; The tunnel is up but other end's addresses is non-routable on my end; We are not allow to make their addresses routable through routing protocol. Can i use NAT on the ...
Dudes, Is it possible to use self signed certificates for IPSec VPN?, I do not want to use preshared keys and third party CA for authentication.If yes how do we do that.Many thanks,Rajesh
Hello!I am confused, ASA with inspect or without inspect.A simple schema 100 0http client------ASA--------http server inside out 100 0http server------ASA-------http client inside out What...
I have our asa5520 (local network) talking lan2lan VPN to a asa5505 (remote network) for a "remote office". I have a cisco IP phone communicating to the Call Manager over the VPN connection. The problem I have is that the phone will reset and come ...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
04-18-2024 11:35 AM | ||
04-18-2024 10:47 AM | ||
04-17-2024 06:49 AM | ||
04-16-2024 07:12 AM | ||
04-14-2024 06:53 AM |
User | Count |
---|---|
7 | |
4 | |
1 | |
1 | |
1 |