Is it possible to setup Access Restrictions to the webgui (IP) in Cisco Prime Infrastructure Version: 2.0 I want to limit access to the webinterface to specific IP's only! Products like Cisco NAC etc. support this feature.
Is it possible to setup Access Restrictions to the webgui (IP) in Cisco Prime Infrastructure Version: 2.0 I want to limit access to the webinterface to specific IP's only! Products like Cisco NAC etc. support this feature.
Dear Friends, is there any guide or document to make VLAN assigment work, i found only video in youtube that do this using flex connect feature mapping? thank you
Is application visibility control working on a foreign and anchor environment? I couldn't get foreign controller show AVC information. Foreign controller has 7.4.121 and FUS 1.9.0.Will bandwidth rate limit in QoS work on a foreign and anchor envir...
Hi,When running the installation wizard (CLI access), I will be asked about Multicast IP address.I don't know what answer I can give.WLC release : 7.6.100.0 Thanks for help...
I have a Cisco Aironet 1100 series access point (AP1120B) that after resetting to factory defaults the default username and password (Cisco and Cisco) aren't working in the web GUI. I am able to telnet to the AP's IP and log in with Cisco and Cisco ...
Hello,I recently configured a DMZ Anchor controller and both control and data paths are showing 'up'. When a user connects the the WLAN they are receiving an IP address from the foreign controller interface rather than the DMZ anchor which is config...
Wed Jun 18 15:39:22 2014 AP 'AP-56 ', MAC: 28:34:a2:b1:86:e0 disassociated previously due to Link Failure. Uptime: 0 days, 09 h 40 m 34 s . Reason: Capwap WTP Event reques
Hello,I would need to route default route from a specific network to a specific ip using pbr. For example I already have a default to 10.1.1.1 .. then I would need another default to 10.1.1.2 applied in ingress on a specific interface (gi0/1) for tra...
Dear All, I did a re-imaging on NCS prime after which I'm getting the below errorPlease help me as to what could be the reason for this error...**********************************************Please type 'setup' to configure the appliance**************...
how i can confiure cisco wireless controller
hello everybody,actually i'm confused so i want to upgrade my WLC 4402 from 6.0.199.4 to last version available and i have my AP 1242G with version 12.4(21a)JHB1 I just want to know what's the version compatibility beween my WLC and AP,thank you for ...
Hi all, I have a WLC with 35 AP configured. In the monitor page of the WLC there is an Access Point Summary Section to show the radios.The 'all APs' section has one more ap than the other radios.Sometimes it will go down to 34 AP's but a page refresh...
I have 10 1142 LAP's that were working at various locations. I have replaced them with other newer model AP's and wish to reuse them somewhere else. I have connected them to WISM controllers to reconfigure but the green status light on each AP no l...
Hi, I have cisco 5520 ASA running 8.4 version. We are getting below logs on our firewall continuously. This has started after upgrading it to 8.4 from 8.2NLDCF2-Ext : %ASA-2-106017: Deny IP due to Land Attack from x.x.x.x to x.x.x.xwhere x.x.x.x is t...
Hi,Couple of pre-sales questions if you don't mind:1. Does the RV220W Wireless-N Network Security Firewall allow RADIUS authentication of wireless clients on the WLAN?2. Does the Cisco SRP 547W Wireless Router allow wireless clients to tunnel into t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-16-2024 12:50 PM | ||
08-15-2024 04:04 PM | ||
07-17-2024 11:11 AM | ||
07-17-2024 06:04 AM | ||
07-08-2024 04:04 PM |
User | Count |
---|---|
22 | |
11 | |
6 | |
4 | |
3 |