Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Insider User Research program

Labels

Forum Posts

I configured an AP to use dhcp, now I want to use the CLI to show which default gateway it picked up.  "Show ip route" doesn't seem to be in its vocabulary.  Does anyone know the correct statement?  Also - for the AP to use dhcp to pick up the defaul...

ippolito by Level 1
  • 78778 Views
  • 7 replies
  • 0 Helpful votes

Hi,We've recently setup a WLAN infrastructure using a WLC2504 and Aironet 1261 LWAP's; two SSID's are configured on the WLC; one configured for Guest [using lobby ambasador] and one configured for Internal use.The requirement to deploy the Aironet 60...

Hi Guys,Can someone give me some advice? Its a bit long but challenging ..••JI am interested in implementing a Multiple WLC environment. I have Three 5508 controllers and 3 buildings (each building approx. 40 APs). I am considering 2 different approa...

jonathan by Level 1
  • 955 Views
  • 4 replies
  • 0 Helpful votes

hi,one of our customers wants to update the firmware of a 5508 wlc, but always gets the following error message:Error Message   %UPDATE-3-INV_FILE_SIGN: Error! Invalid image signature!. Image may be corrupt.but the same image works fine on another 55...

flokki123 by Level 3
  • 1266 Views
  • 3 replies
  • 0 Helpful votes

hello friends,if we have 2 cisco 2504 series wlcs and use multicast fetures in both and both are primary and secondry for LAPswhat about of we use multicast ip address let's say 255.239.1.60  can we use the same ip address for the secondry contrller ...

Hi All,I am able to view clients, rogue APs, rogue clients etc, but the information is faily inaccurate. Thus, I am trying to calibrate using the RF calibration models. I have created a new model and am attempting to add data points.After adding the ...

hi,one of our customers wants to update the firmware of a 5508 wlc, but always gets the following error message:Error Message   %UPDATE-3-INV_FILE_SIGN: Error! Invalid image signature!. Image may be corrupt.but the same image works fine on another 55...

flokki123 by Level 3
  • 656 Views
  • 1 replies
  • 0 Helpful votes

WCS fails to start with a Tomcat error , see below ;See launchout below - any ideas - without re-installing WCS Checking for Port 21 availability... OKChecking for Port 8456 availability... OKChecking for Port 8457 availability... OKChecking for Port...

rwilletts by Level 1
  • 2386 Views
  • 8 replies
  • 0 Helpful votes

Hi,I have an AP1242 that I am trying to set up but whenever I plug it in, it will go straight to the image recovery (pink status, red radio LED) and display the following:Xmodem file system is available.flashfs[0]: 148 files, 7 directoriesflashfs[0]:...

aatrout by Level 1
  • 1129 Views
  • 6 replies
  • 0 Helpful votes

Hellowhat is the ideal timeout for users when no activity is performed while connected to network via wirelessWLC model 5500AP model 1200 seriesusers get disconnected every 15mins when machine is Ideal and where do i see this optionthanksST

Dear AllWhen i am trying to make test between  two of AP 1142-N as ((WGB & AP) scenario & (root bridge & non root bridge)scenario). but it's fail.so i thougt the problem with IOS .. after delete old one and reupload another i have new problem.. the p...

Hi all,Here is my case.I have a WLC 5508 connected thorugh Giga 0/1  to my core 3750 switch and through that to my access switches were my APs are plugged. Everything is working fine , multiple SSIDs, DCHPs, security ,roaming ....etc. My plan is to c...

smartns04 by Level 1
  • 1641 Views
  • 5 replies
  • 0 Helpful votes

hi,How to set up wireless LAN controller and what and all minimum parameters need to configure it ? what and all additional device required for it ?.As I planned to run 20 AP in a small compound with LAN controller.please help me find the sameThanks ...

afath by Level 1
  • 890 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card