Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi at all,another problem or maybe a nice feature in the codes 7.4.100.0 and 7.4.100.60 is when the TX is on automatic allAP´s change the tx power very often and including interface resets. In a voice environment is this not really possible.In the co...
As i configure on the attachment . the three LAP register successfully on the controller .the problems :1 - users who access EAMCO-core and Guest-Core , access successfully and gets IP but users who access EAMCO-Dist and Guest-Dist can't get IP " i...
Hi all,Can someone please tell if it's possible to use existing AP license number from an old 4404 WLC to a new WLC 5508 ?I know that the 4404 has hard licensed bounded to the controller, not like the 5508 adder licenses that can be purchased separat...
Hi,I'm looking after a NAC solution for many reasons, among of them is that I use FreeRadius and I want to autodetect and auto register the MAC addresses of our wireless endpoints and after that I will only permit access to those MAC addresses alread...
Good Day, I would like to connect to Cisco's management WLC via wireless. There is a security feature that allows you to ENABLE or DISABLE WLC management via wireless. I have enabled controller management to be accessible from wireless clients i...
We have a Cisco 4400 WLC with about 70 Cisco AIR-1131AG-A-K9 access points. The controller runs and the access points run 4.1.171.0 code. We work in a hospital enviroment and nurses from one of our floors (3N) are complaining about poor/low signal ...
Hi all,Forgive me for not finding it on my own since I am sure it exists. Does anyone have a link to a support chart that shows where support for APs stops on WLC 7.4 code? Specifically, while running APs in Flexconnect mode? Thanks in advance
Hey all,I have a TAC case open, but it doesn't seem to be making any progress....I upgraded my 5508 controller from 7.2.111.3 up to 7.4.100.0Most of my APs are fine. 3500s, 1100s etc.except for 602i APs. The APs associate, they update software etc, b...
Hi,I'm going onsite to look at a 5508 (don't know exact config or code version until I get there) that has stopped displaying the guest authentication splash screen but apparently still allows access. What might cause this? I can open a support case ...
When using Guest Access Cisco recommend a Mobility Anchor Controller be placed on a DMZ and the guest access wireless Lan is tunneled to this controller. This means that 2 DMZ subnetworks are required - one for the management interface and one for t...
I have an access point at a branch office. I have added it to a flexconnect group because I only want the local SSID and the centrally managed guest SSID to be broadcasted. I am not sure how the switch port needs to be configured though. I have a 'gu...
HI Memebers, I have a virtual controller and the AP keeps connecting and disconneting .Number of Traps since last reset 81 Number of Traps since log last viewed 32 LogSystem TimeTrap 0Tue Nov 20 19:13:00 2012AP Disassociated. Base Radio MAC:0...
Hi guys,I need a ppt (power point) for Cisco Wireless Lan Controller and WCS. I need to make presentation today. Please help me guys. I already look it over the internet. I didn't find. So, Please help me.BRTotardo
Is it possible to move a LAP associated to a WLC to another WLC?Can i do it from WLC or WCS?thanx marcello
Hienabling 802.11k on wlan, clients that do not support it are able to work and connect to the network. Clients that do not support it can ignore it?
