Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

I was wondering if anyone would happen to know what thelow, medium, high power settings are on the AP541N in either dBm or mW?The data sheet indicates what the maximum/full power settings for 2.4 GHz are:802.11b 15 dBm802.11g 15dBm802.11n/20 MHz 12 d...

tsawchuk by Level 1
  • 707 Views
  • 0 replies
  • 0 Helpful votes

Hi folksI downloaded an authentication bundle from Cisco website, It is a .tar file. I need to edit the .tar file by doing the following:Remove Cisco Logo and put a new logo inside it.Edit the login page to fit with the deploymentImport the .tar file...

Elie Sbat by Level 1
  • 3771 Views
  • 16 replies
  • 0 Helpful votes

I am having trouble with a wlan at one of our locations.  This problem occurs randomly with most of the users there but in the example below I have included the most troubled.  The clients experience awful wireless performance and response times for ...

LEN SNEED by Level 1
  • 1310 Views
  • 3 replies
  • 0 Helpful votes

Hi everyone,As Cisco TAC engineer, I thought this medium is a good way to gather good opinions. So please leave a message saying what document you think is missing from cisco.com about Wireless products. Config examples, white papers, troubleshooting...

It seems this product was discontinued?What are people using out there with similar functionality?I never used this product but purportedly the readout was friendly so you did not have to be a RF engineer to understand it and make good use of it.If m...

lcaruso by Level 6
  • 4252 Views
  • 7 replies
  • 0 Helpful votes

On an autonomous 1131 AP, I'm working with someone else's config and trying to understand why a hold queue would be placed on this interface and if it is helpful or detrimental for this AP to have it enabled. interface FastEthernet0 no ip address no ...

lcaruso by Level 6
  • 1640 Views
  • 1 replies
  • 0 Helpful votes

On an autonomous 1131 connected to a Cisco 2960 swtich, these vlan names are defineddot11 vlan-name DEFAULT_VLAN vlan 1dot11 vlan-name Internet_Only vlan 999they are not used anywhere else in the config. Are they intended for local use only, or can t...

lcaruso by Level 6
  • 491 Views
  • 2 replies
  • 0 Helpful votes

The Aironet 1130AG Series is available in: A lightweight version An autonomous version that can be field-upgraded to lightweight operation A single-band 802.11g version for use in regulatory domains that do not allow 802.11a/5 GHz operation Is this...

lcaruso by Level 6
  • 481 Views
  • 3 replies
  • 0 Helpful votes

Hello,I'm planning to purchase couple of 1142N aironets, and would like to know if they support Root bridge & Access point and Non-root bridge & Access point modes simultaneously on different SSIDs.So the plan is to create wireless bridge between two...

assuming two ssids on both radios, such asdot11 radio0ssid Privatessid Publicdot11 radio1ssid Privatessid Publicdoes a given client--which is capable--automatically display/select the 5Ghz radio over the 2.4Ghz?Specifically, when the 5Ghz-capable-cli...

lcaruso by Level 6
  • 449 Views
  • 2 replies
  • 0 Helpful votes

On an autonomous 1131, what is the effect of not having antenna gain set to 0?interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers tkip ! encryption vlan 1 mode ciphers aes-ccm tkip ! ssid Private ! ssid Public ! mbssid s...

lcaruso by Level 6
  • 6797 Views
  • 7 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card