Wireless

Hi Sir,My customer has the following unified wireless guest access requirement:- There are 2 internet links and dmz zones at two different locations, Site A and Site B- Data centre is at Site A- WiSM is proposed to be installed at the Cat 6500 in Sit...

Hi All, Is it possible to deploy WLC redundancy over L3 link???In our scenario we have 2 controllers located in 2 different sites, the link between the site is L3. AP's are deployed across four other locations, two are coming to site 1 and rest two a...

I have 2 WiSM blades (4 controllers) in a 6513. The goal is to upgrade from 4.0.179.11 to 4.1.185.0 which requires an intermediate step of 4.0.206.0+.I upgraded the first controller to 4.0.219.0, and now I can ping the WiSM and can session into it fr...

Hello:I just installed a 802.11a/b/g card with winclient version 4.2 installed. after reboot, i could not even get back in the xp system any more. before the loading the driver, the system didn't require password, now it pops up "log on" and ask for ...

I am getting the following error below from a 851W router. Any ideas as to what is causing this?Not encrypted dot1x packet from 001c.bf83.2a21 has been discarded

Hi,I try to configure a WGB in autonomous mode to connect to a lightweight access-point. I followed the cisco paper about it and my wgb associate well to the AP on the asked SSID. From the wgb i can ping stations behind the lightweigth access point s...

Hi,I'm using cisco 4402 with a few AP's to boardcast SSID and manage all AP's. I want to know is there any way for me to get alert when someone can successfully connect to my network instead of login to the management console to check?Thank you!!!

I have a LAP1131G-A-K9 with C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, System image file is "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"I need to revert from LWAPP mode to autonomous mode but I don't know what IOS should use.Any suggestion?

Hello All,Does anyone know if there is a way to get the WCS or WLC to report if a change had been made via syslog or snmp? Also, is there anything specific that has to be configured in the WCS to send emails of traps or alarms? I see where there are ...

Anyone know where I can get this module?http://www.cisco.com/en/US/docs/wireless/wlan_adapter/eap_types/fast/admin/guide/EF_instl.htmlAlso, can I use EAP-TLS or EAP-FAST (with certs only, no PACs) and authenticate users via LDAP (AD) without the need...

Our WCS shows the following events for some APs:AP x with protocol '802.11a' on Controller y is contained as a Rogue preventing serviceThe problem I have with this message is that the affected APs are 1231 and do not have a 802.11a radio interface at...

he environment:---------L2 SWITCH---------| |AP APAP AP| |---------L2 SWITCH---------I've configured load-balancing src-mac on 1st side (pc lan) and dst-mac on the other side (router lan)."The default is to use the source MAC address. This default me...

I am using 2 CISCO 4404 controller and 160 lightweight access point. In my network I have 2 6509 core switches 1 main and other backup with FSWM module. I have 11 floors in the site so I created 11 context as per customer requirement. Now the problem...

Hello everybody,We "inherited" an Aironet 1200 access point with antenna's throughout our building. This was installed by a company that thought they would make money selling Wi-Fi access but now they have gone bankrupt.We eliminated their router and...