Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Is it possible to use PEAP-GTC without re-entering credentials after the client roams?Configuration is as followsRSA RADIUS, SecurID tokensWLC 2106 4.2, LAP1131Dell 630, Intel 3945abg, Windows XPJuniper Odyssey 4.52WPA TKIPCCKM enabled on the WLAN
Morning,I need a little direction as to where to go next in my implamentation. We have LWAPP AP's with Cisco WiSM controllers and WCS, I configured WPA-TLS auth and that works fine but when I try to tell ACS to make a Radius call to our RSA server, i...
We have a 1300 root bridge sitting on the outside of a building. I configured and installed a 1231 in another building adjacent to this building. The line of site is perfect. The 1300 can see the 1231, and has it in its association table as a WGB, ho...
Situation, new deployment with several controllers. 1130 access points in a low to medium density environmnet. Did a very basic install (no changes to DCA) and configured DHCP and DNS for discover. All access points come up on channel 1 and 36. Dynam...
Yesterday I was setting up a couple of "guest" accounts when the GUI and command line for one controller in a WiSM became non-responsive. Now, I can access the web GUI but only the Menus are displayed. In addition, accessing the CLI takes forever. Ha...
Hello,Excuse the newbie question, but I am trying to validate the throughput between a pair of Aironet 1410's. Would using the command:dot11 dot11radio 0 linktest rate 54 packet-size 1400 count 1500 target <mac address of other end of bridge>Work for...
I am having a problem configuring the daylight time setting on both my WLC4402 Release 4.1.191-24M. Although I could enter the NTP Server under Controller- NTP I still need to add + 2 hours from Delta in the Timzone setting so that the time will refl...
HiI am in CanadaI am trying to configure an AIRONET 1310 with INTEGRATED antenna to work as an access point for clients on a campgroundThe range I get is awfull (50 feet and I loose the signal completly)the aironet is outside and no tree are blocking...
I attempted to setup WCS to auth admin users against our ACS and failed miserably. Now I can't log into the web interface of WCS at all. Does anybody know how to reset the WCS AAA setup from the command line?
Dear sir,I have two aironet 1250AP and I would like to build wireless connection as below,could someone tell me if I need to adjust some settings(such as acktime out...) for long distance connection? thanks for your help. wirelessly B1-----1250- - - ...
Does the antenna ship with a Mast Mounting Kit or does that have to be ordered separately? If a separate kit is required, what's the part number?
Our customer has about 200 Autonomous APs(Version=c1200-k9w7-tar.123-2.JA2),WLSM(Maintenance img(1.1(2)),Application img=12.2(15)XR2), Sup720 IOS=s72033-jk9o3sv-mz.122-18.SXD3.bin.The static WDS point to WLSM,somme of AP will fail with log"Connection...
Hi all,we are using 3 AP Aironet 1131 (Version 12.4(10b)JA3) in a WDS. All are connected to a Switch Catalyst Express 500 to receive their Power. The Problem is they work for some time and the the AP reloads without further errormessage. Speed and Du...
hi i am looking for someone to configur the aironet to work with 7920 phone, i ha smy aironet working fine but i dont know how to integrated it.
Hi,On my wired network I have VLAN10 (for production network computers) and VLAN192 (for Public Internet access on a separate circuit.) We purchased a Cisco 4404 WLC, and are now using WIFI to access VLAN10. My DHCP Server on VLAN10 is 10.6.0.198, an...
