Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Insider User Research program

Labels

Forum Posts

Hello,I am running VxWorks ver 12.02 in my 1200 and 350 I have several wireless clients (Compaq multiport, ActionTech USB and Cisco 350 PCI). In the Association table on the AP sometimes the AP deathenticates due to Inactivity. Is there anyway to n...

tlchant by Level 1
  • 2859 Views
  • 1 replies
  • 0 Helpful votes

Hi,i have 2 point to point bridge 350,and only wep is active,i know how to make radius with AP 1100 and client (pcmcia)I want to know how i can secure my point to point connection. root --> no rootIs possible to set root on radius serveur and to set ...

albatore by Level 1
  • 442 Views
  • 1 replies
  • 0 Helpful votes

In VxWorks versions there was a setting to allow/disallow for “Default Unicast Address Filter” for each authentication type. This setting is found on AP Radio: Internal> Advanced>Primary SSID setup more…. This setting must be set to disallowed for se...

Due to security issues, both the CDP and SNMP protocols are disabled. I am unable to discover a device when I enter it in manually via just the IP. The run log shows:Seed value entered: 10.50.33.254Seed value entered: 10.50.33.253Seed value entered:...

admin_2 by Level 3
  • 829 Views
  • 7 replies
  • 0 Helpful votes

Just migrated some of my users from wired network to wireless network. Both wired and wireless are on different segment.So of them still prefer to connect via wired while sitting at their cubicle and at the same time their wireless card is also turne...

jazzzz by Level 1
  • 807 Views
  • 4 replies
  • 0 Helpful votes

I'm considering deploying a wireless network between two of my buildings, the issue is that I'm in close proximity to an airport. I seriously doubt that this would be a problem (after al, why would the FCC ratify a standard for buisness use if it wa...

Placate by Level 1
  • 275 Views
  • 1 replies
  • 0 Helpful votes

I'm trying to use EAP-TTLS with a 350 client and having a problem in that the settings to enable WEP are all in ACU, and not accessable when using Windows 2000 and other supplicants. None of those setting are on the device configuration, as they are...

hkfiedle by Level 1
  • 403 Views
  • 2 replies
  • 0 Helpful votes

Any idea about QoS mechanisms on AP1230 : For instance (I prefer CLI) :- if I want to reserve 50 % of bandwith to vlan10, 30 % for vlan30 and 20 % for vlan50- If I want to reserve bandwith by protocolPlease forget the MAC add cause it is not what I a...

Mark3000 by Level 1
  • 282 Views
  • 1 replies
  • 0 Helpful votes

Hi,I have an AP 1200 that I want to configure in repeater mode, but when I do this it stops to respond to the IP address. Traffic throw the AP works just fine, but I can’t access it via IP only buy console.(running ios 12.2.13-JA2)Any Ideas on what i...

rwedham by Level 1
  • 271 Views
  • 1 replies
  • 0 Helpful votes

I have an AP340 running VxWorks 12.04. If I navigate to the 'Manage Installation Keys' page (Setup, Cisco Services, Manage Installation Keys). It shows the device type as AP4800-E. Is this a known problem or is it a dud?Andy

Does any Access Point from Cisco support the Contention Free Mode (PCF) according to the IEEE 802.11 standard? And if yes, how could it be enabled and configured?

r.leutert by Level 1
  • 472 Views
  • 2 replies
  • 0 Helpful votes

I've tested Linksys WAP11 connecting to BR-350 and works fine, but not with AP350.Is there any configuration options in AP350 that may allow generic 802.11 connections ?I tried (no aironet extensions + bcast essid).Luciano Lima.

Review Cisco Networking for a $25 gift card