Wireless

I want to know how far is the AP1242AG's able to comunicate with wireless client? Is it possible to extend about 1km coverage AP1242AG(AP mode not bridge mode) with high dBi antenna?I think that the AP1242AGs is not like as BR1300 or BR1400, so AP ha...

Hello,we are using PEAP authenticaction with ACS 3.2 and MS CA (server 2003)... Certificate on ACS will expiry soon. Are there any recommendations, steps how update (reinstall) certificate ThanksM.

I could use some help. I have a pair of Cisco 1200 AP's that I'm trying to use as bridges. I have selected one as a Root Bridge, the other as Non-Root. The non-root shows the wireless interface down and the log reveals 'no association'.I have verifie...

hello experts!!!can traffic pass through 11g to 11a and vice versa. please have a look at the attached drawing and see if any of you can share any practical solution.the idea was to use the APs as repeaters on the three trucks and not to use bridges ...

Having a CCKM issue that is really annoying my customer. TKIP is configured with CCKM and is using LEAP for authentication. A WDS is setup and works great except for these issues. Clients attach and roam but 1-2 twice a day up to 6-8 times a day, cli...

I have (2) networks going into an ap 1200 - the AP has a static ip set on it as 192.168.199.210 which is vlan 20the other network is from my DSL to have wide open wireless for guests (vlan100) that ip in the router is set at 192.168.199.51 (scope is ...

If I bought the current WLSE product (CWWLSE-1133-K9), this comes with software 2.13. Would it be possible to downgrade the software to 2.7.1, which is what I have tested and certified?

Does anyone know of a config example for LAN (VLAN1) off F0-3 plus AP Wireless Access on a Cisco851W?Thanks,Bob

Has anyone else experienced an issue with the AP1131ag access points flooding the network with igmp packets? I have an AP1130 already in service which did not cause this to happen. And this has happened with 2 AP1131 that I have taken out of the box....

Hi All,I have been checking the "Cisco Systems Aironet 1310 Intallation" manuals, and have noticed that the external antenna model has connectors for two antennas.My question is if this device could be used as repetitor (logically splitting the signa...

Hi ,I am testing basic L2 LWAPP and am having problems getting the AP's to register with the controller.If I run a "debug lwapp error enable" I get the following error message:"Mon Jun 5 17:22:00 2006: AP 00:0b:85:24:89:d0: Regulatory Domain (0x0001)...

Well..I have the following devices:WCSWlan controller 4402AP 1130 LWAPPWorkstation XP sp2Secure ACS 4.0Windows CA Windows AD---------------------Everything else is working properly, except EAP-TLS. Server certificate is installed in ACS and trust lis...

Hi people,I´m installing 3 AP 1232(dual), documentation says they support 802.11a/b/g, they support it at the same time or it is up the anntena ?Martin Cordero

I am proposing to install three AP1242 and want good coverage within a warehouse, so am looking at the ANT-2460P patch antenna. Do I need 2 of these per AP and how far apart should the antenna be placed apart. I need to cover a working height from 4 ...

I am installing a second WiSM blade on a redundant (backup)6509. The A&B side of the produciton WiSM were spec'd to run <= 300 APs. How does one configure these control units so that production runs on WiSM blade 1 and fails over to WiSM blade 2 on t...