Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

We have successfully piloted EAP-TLS with machine certificates for wireless using microsoft IAS and I am investigating converting to ACS for the radius piece. One thing I can't figure out how to do with ACS is to check policy settings for the supplic...

dmcconnell by Community Member
  • 498 Views
  • 1 replies
  • 0 Helpful votes

Hi,I just configured a WLSE for out 5 APs. All APa are 1200. Four of them with .g radio and one with .b radio.The WLSE identifies 3 of the 4 .g radios as .a with strange implications: In the location manager the correct channel in the 2.4GHz range ar...

t-wieczorek by Frequent Visitor
  • 451 Views
  • 1 replies
  • 0 Helpful votes

I'm trying to get the number of clients associated to my 1200 APs which have dual A/G radios using SNMP. When I use the usual OID (the same one I use for my 1100 series APs) I get a constant 1 for the # of clients. I've tried many variations on this ...

nagle by Level 1
  • 702 Views
  • 1 replies
  • 0 Helpful votes

Hello !I'm developing an application under WinCE and i'm testing it with an AIR-PCM 352. It scans all wireless networks. I use NDIS 5.1 and i recover all informations (BSSID, MAC adress, RSSI, frequency...) but not the noise. Does someone know how to...

vincentxx by Community Member
  • 343 Views
  • 0 replies
  • 0 Helpful votes

I have a 1200 series AP that I was able to access via terminal connection last week. It has not been configured for use yet. Today the status LED is amber and the radio LED is red. Every time the unit is powered down and up the same LEDs appear. The ...

francisjad by Community Member
  • 642 Views
  • 2 replies
  • 0 Helpful votes

I have a couple of 340 AP devices. One of them would not allow clients to access the network any longer. When using the web management interface the AP Radio interface is not even present now. I have upgraded the firmware to 12.04 and attempted to re...

gparrish by Community Member
  • 761 Views
  • 2 replies
  • 0 Helpful votes

Can a 1310 bridge operate also an Access point? I know the 350 series bridges could not work as an AP, but in the Cisco documentation it states that the 1310 is a wireless bridge/AP. If it can work as an AP can both the bridge and the AP features be ...

skilambi by VIP Alumni
  • 1017 Views
  • 3 replies
  • 0 Helpful votes

Hello,I am trying to run wireless video over our wireless link and with the Cisco 1200 running at 54Mbps vs. 11 mbps. The 11 out performs the 54mbps by a wide margin. The AP is running IOS 12.2(13)JA. I will try upgrading to JA4.Any thoughts.

tlchant by Level 1
  • 753 Views
  • 2 replies
  • 0 Helpful votes

hello can any body tell me about VSAT (very Small Aperature terminal) and DSS(Direct Satellite System)complete solution and toturial about that....or any web site that provide me complete solution and understanding.....thank a lotirfan aslammirfanasl...

Dear Sir,I would like to know whether AIR-AP1230B-A-K9 comes with any power inline injector such as AIR-PWRINJ3 or I have to quote additional part number which is AIR-PWRINJ3=?Thanks.Delon

c.ong by Level 3
  • 747 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card