I have an internet gateway, with its own WiFi, running a DHCP server. I connected my MR57 to one of the ethernet ports and setup a 6GHz-only SSID in bridge mode. I connect my clients to the SSID and they get a DHCP address from the server on the gate...
We are migrating APs from our existing Cisco Catalyst 9800-CL WLC running IOS-XE 17.9.3 to a new Catalyst 9800-CL WLC running IOS-XE 17.12.3.Instead of moving all APs within a single maintenance window, we are performing the migration on a site-by-si...
Hi,MR 32.2.5 is now available with some fixes.https://documentation.meraki.com/Wireless/Product_Information/Compatibility_and_Firmware/MR_32.2.5_Release_Notes
Hi ,I'm trying to understand the values returned by AirMarshal. I'm seeing SSIDs near my APs with some anormal values : I'm no wireless expert but a RSSI of 137db seems impossible. I can find approx 100ish other SSIDs on multiple sites with those val...
I’ve got around 1200 x 2800 APs to migrate from 5520 -> 9800, over 2 site, pre installing image, then change the Primary and priority of the AP.1 Site is a has the standard Hospital H Blocks build with multiple levels, with 4 wards on each.Looking at...
I have a 2802 AP that is associated to a 9800 controller. I am trying to log in to the AP, but get the message: No valid user found, please configure a valid user from Controller I cannot find this setting anywhere in the controller. (Of course, I k...
Have a couple of these C9130AXE-E , not able to join the wlc , error/s DTLS Handshake Success and the Heat beat timer expiry . how to resolve this without having to console to the actual access point current wlc ios ver 17.12.7a
Hi Folks,I have a wave2 controller. I have a guest wifi that is currently using the management interface. I want to change the interface to use the correct one I have created for the guest wifi however every time I do this I get the below error.The f...
deploying AI-Enhanced RRM for a single site which has same RF-TAG as rest of the sites, when configuring CatC pushed this configuration, without getting into exact RF parameter details. wireless profile multi-bssid AI-RRM-PROFILE-BASICdescription AI-...
I have a C9130AXI that won’t complete an APSP upgrade. It joins my C9800-CL, fails to unpack the new image because its inactive partition is full, and reboots every ~4 minutes. Two other C9130AXIs on the same WLC upgraded fine. I think part1 is full ...
During boot, 9130 AP running 17.18.x does not show the expected autoboot break command. I'm expecting:Hit ESC key to stop autobootInstead, it just goes straight into booteth0 Auto boot mode, use bootipq directly APPS power cycled and restart reason i...
Hello,I'm tasked with updating our WLCs. We have two that have a Mobility group attached to them, one acting as the primary and one as the secondary. I am somewhat familiar with the methodology that the backup WLC should be updated first before the p...
Hello Teamclassic case with DTLS handshake failure due to WLC doesnt trust VAP's MIC.vap-0#sho inveNAME: CW9178, DESCR: Cisco Catalyst 9178 Series Access PointPID: CW9178I, VID: , SN:WLC#sho inveNAME: "Chassis", DESCR: "C9800-CL Chassis"PID: C9800-CL...
Hi, what is the best way to learn Cisco Meraki Wi-Fi (primary), and networking today, 2026. Any updated online education at Cisco?
Hello All. Have a CW9800M Wireless Controller to mount in a data center rack. It comes with ears for a 2-post telco rack. The Hardware Installation manual indicates a 4-post rack mounting kit is available but does not show a part number. Have tried n...
