Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi,l have the following issue with WLC C9800p2p communication within WLAN does not work when the option „Passive Client" is checked.how can we make it work with „Passive Client" enabled;RegardsBoris
Hello,#we have a centralized WLC to manage all remote sites APs with local switching modeone SSID with a lot of VLANs for every team#All clients request IPs from centralized DHCP at DCwe have business requirement to have each site use its local pool ...
Hello guys,I have AP1830 working as mobility express controller and have 27 access points, no vlans configured and dhcp is enabled from a firewall. When I started to connect the AP to the wld, I found only 12 out of the 27 and all the access points a...
hi guysI am planning to connect lately released APs(9XXX Series) to the wireless controller(5500), then there will not be any compatibility problem??it can be working properly without any problem??Thanks.
Resolved! Run Latency - 9800 Mobility History
Hi Team.. In a 9800 controller if I look the client statitics in the tab Mobility History I have the value "Run Latency" in ms What's Run Lantency means... I tested the connection from the wlc and the cliente to the default gateway and I have values ...
I have a new Catalyst 9130AX AP which boots into WNC Linux instead of IOS XE. The LED does not work and neither does the factory reset procedure.If I interrupt auto boot by pressing a key, it goes to a U-Boot like shell called "Axel". I've posted "pr...
i have existing Aironet AP in my environment and have plans to add Meraki MR44 AP side by side.would there be any issues for them to work in bridge mode so that both can work in the same office using the same set of SSID for my clients ?
Сеть из 3х точек доступа 1815w на mobility express. Канал 100мбит. По шнурку в роутер - скорость примерно 90 и на скачивание и на загрузку.У точек доступа входящая скорость 90, исходящая 30 :((( И по воздуху, и при подключении в порты точке доступа.....
spec C9120AXI-FEWC 17.6.1client iphone 12 pro max and ipad pro m1 setting disable private address problem can’t connect to protocol 802.11AX / wifi 6 and 80mhz channel in ac slow throughput test in iperf3 130mbps with server connect to cabel 1gb port...
A direct connection with the client AD was enabled, to correct a problem with the ACS, but it gives credentials error.It could be that the container is wrong indicated. (Cisco Controller) >show ldap summaryIdx Server Address Port Enabled Secure Bind...
Resolved! 2802i is enable to join Controller
Hello, I have a 2802i as a Mobility Express Controller with 5 APs (2800 and 1830 Capwap and ME), I am trying to add another 2802i but it can't joun the controller.I tried to upgrade the AP to the same version as the controller (8.10.130.0) when I use...
I have a question with the HA of the WLC 9800,can I do a HA with a physical WLC and a virtual WLC ???
Saludos, quisiera solicitar de su ayuda a saber de qué manera puedo acceder y configurar una dirección estática a un Punto de Acceso Cisco (AIR AP1815I A K9), estos creo que no vienen con una IP configurada para poder acceder a la configuración por d...
I am trying to put an image back onto an Access point.I have followed the guide which is on this site and it is not working for me.Here are the stages i have done so far.Set up TFTp server and set my IP to 10.0.0.5.Reset access point, while connected...
Software Version: 8.10.151.0 (WLC8540)AP 9120AXI-xAIR-PWRINJ6= on switch: that ap get ip address but not join controller. the version ap open box ap1g7-k9w8 8.10.130.0other AP 9115axi can join
