Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi,Is it possible to set up TLS 1.1, 1.2, or 1.3 with the Cisco Cisco Aironet 2600 serie?If so, do you know how to do it?The last firmware release 15.3.3-JF15 ; does not mention TLS versions compatibilityhttps://www.cisco.com/c/en/us/support/wireless...
Hi is there a Way to get a list from Rogue AP´s where sending with 160 MHz Channels ? I could extract it from the CLI on a C9800 but i am looking for a much elegant solution. Maybe someone knows how to get this information from Prime or DNAC. Conten...
We experienced Issues regarding network-connectivity, I looked into some loggs on our WLC 9800 and saw a bunch of loggs like this:.Oct 11 15:51:27.768: %IOSXE-4-PLATFORM: Chassis 2 R0/0: cpp_cp: QFP:0.0 Thread:224 TS:00001035332249163839 %SWPORT-4-MA...
Dear Meraki,When I try to update my AP I get this error.There were errors in saving this configuration:One or more errors occurred. No changes have been saved.Firmware Upgrade failed due to the following node_groups: XXXXXX. Firmware Versions MR 28 a...
I am looking for the factory reset procedures for a Cisco Aironet AIR-LAP1142N-A-K9? I tried the usual procedures without success. I do not have the login credentials or secret password.
I have a problem with backup configruation from WLC 9800-L via TFTP. I get this message "Error in Configuring Backup & Restore Error opening file connection timed out " when I set backup. I have set up automatic backup (archive) on switches in this n...
we have 1832 wireless environment, and now need to additional aps, due to eol we can not by 1832 aps. therefore we are panning to buy catalyst 9115 ewc and use on same environment with 9115 ewc.
Hi, my printer HP 9022e does not print from my iPhone when I am associated to AP 3500 to WLC 2504 with 8.5.182.0 running code. The reason might be this: (Cisco Controller) >show mdns service srv-not-received macAddr Service-Provider-Name Srv Query Se...
Hello everyone,I have an issue adding Capwap ap's to the controller, It all started when I had to reset my ME ap since it was not transmitting WiFi signal, and after the WiFi issue is resolved and reconfigured the ME ap, I'm not able of adding the Ca...
Hello, the below is protocol for C9800 wlc initial config. it configures physical port TwoGigabitEthernet0/0/2 as mgmt interface. We want to use layer2 svi as mgmt interface. but if we do so, it would not let us to access wlc via gui. do you think so...
HiIs there any way to display cdp information of APs on c9800 (17.6.3) controller in GUI? I am looking for the command output of "sh ap cdp neighbors" in the GUI. AirOS based WLCs had an option to view this on GUI Home> Network summary > Access point...
I currently have a cisco 5500 wireless controller and one of my ports are down, how do I either bring this port up manually within the CLI or GUI or change the physical status from auto negotiate to Full Duplex 1000 Mbps to match the other ports?
Hi Experts , I have one issue to troubleshoot wireless printer device.Issue is :One user is unable to give the print every monday at 5:00am-5:15am CET .So during this time the printer device goes unreachable from the source .Means ping from Source se...
Hi all, When updating software from tftp server through GUI, the update stops before downloading the image from tftp server with failure reason: configuration error and installer log error:FAILED: install_add : Default profile addition failed due to ...
Good Day,I have just installed 18 new Cisco 140ac access points in one of my school networks. WIFI is working fine, devices are connecting and no issues there. Using the Management Web GUI, I can see all 18 APs, but sometimes they won't have the st...
