Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hi, pretty new to this so please be gentle. We have a WLC that we setup for wireless Mac authentication on the local WLC database. I want to move this list of mac addresses to ISE. I am following a tutorial which says to create an endpoint identity g...
Resolved! WLC 5508 Debug Client SSH session
Hello everybody! WLC 5508 controllerWhen collecting debug (debug client <mac>) I ran into a problem: it breaks the ssh session.Before debugging, I enabled config session timeout 0Please advise how to solve the problem.In Putty, there are no settings ...
Folks,I have recently purchased a Catalyst C9117AXI-EWC-B access point. I have been slowly finding out what this does. I have read almost everything that has been written about these but I have a couple configuration questions. First I see something ...
Resolved! radius dynamic vlan assignment
Hi,Quick question, when assigning vlans dynamically to wireless clients based on different radius profiles, are dotq1 tagging required on the access-points?
In our office Going to Purchase C9800-L-F-K9 Controller. and C9105AXI-E Access Point. But We are already using AIR-AP1832I-D-K9 Access Point here. Will C9800-L-F-K9 Controller support AIR-AP1832I-D-K9 Access point?. Please Clarify my doubt.. I really...
Hi ! I'm having an issue with the C9800 interfaces (on the Bengaluru 17.5.1 version) on an hyper-v setup. My virtual machine can only have one giga interface on the hyper-v vswitch (untagged).Is there any way to configure the giga1 interface so the A...
Hi to all, I have AP 1850 with Mobility express. There is 3 SSID's on that AP, one of them is for guest network. Everything works fine except one issue, I can access ME controller from guest network. I cannot access any other device in other vlans, e...
We have got the WLC9800 controller and the cisco 9115ax-e AP. Im having issues connecting the AP to the controller. I have manually configured static controller address on the AP but it doesnt seem to connect. It sends out the discovery packet but do...
Planning to implement a wireless network having 1572 series access point, which will be having both omni and directional antenna. In a single AP, shall we connect 1 x air-ant2513p4m-n=(directional antenna) & 2 x AIR-ANT2568VG-N=(omni antenna) to serv...
Hi,I have a network with five 240ACs indoors, for the same network I need to add a new outdoor Ap, what model can I use?Thank's
Hi, Thanks in advance, Can I connect Cisco AIR Ap 1832I access point with Cisco Ap 1852i controller.
Resolved! [CG418-E] IOS XE Software upgrade
Hello,I'm testing the Cellular Gateway CG418-E. When I try to upgrade that CG418-E with IOS XE Software release Amsterdam-17.3.4a (downloaded on https://www.cisco.com/c/en/us/support/routers/catalyst-cellular-gateways/series.html#~tab-downloads, Prod...
Does anyone have an .ant file for the Cisco AIR-ANT2568VG-N antenna?It is for an RF Planning tool.
I have a 618,000 sqft warehouse I need to upgrade wireless to. I'm limited with deploying 9120axi for this one. The survey shows moderate coverage for a -10dB barcode offset with 24 Motorola APs, which are currently at maximum transmit power. APs are...
Hello world! What's nowadays the common way to connect a remote building (access switch) via wireless to the (wired) network? In the past often standalone APs configured as Workgroup Bridge (WGB) were used. What's the recommendation today? I don't wa...
