Hello, I working to transform a Cisco AIR 1815i to express mobility using AIR-AP1830-K9-8.2.110.0.tar file, i used this command:"ap-type mobility-express tftp://192.168.2.20/AIR-AP1830-K9-8.2.110.0.tar"I'm getting this error:#ap-type mobility-express...
Forum Posts
Hello Experts, I have a project requirement wherein the scale ability is the major concern. We have a limitation that we would not be able to have dedicated server for Prime and VM is the only optionCan we have the VM provisioning with same hardware ...
Good day,Is it possible to list multiple CRLs within the configuration of a 5508? We have two separate PKI environments with two unique CRLs. The 5508 is currently config'd to point to one of those CRL URLs but we want to be able to have both there...
Hi there, trying to update the cert forWeb Auth on WLC5508, Firmware 8.0.152.0Started using OpenSSL 0.9.8 for creating a CSR.req −new −newkey rsa:2048 −nodes −keyout mykey.pem −out myreq.pem Worked well so far. As we wrote in some posts, we used a Pa...
Hi All As the title suggests i have a Cisco Virtual Wireless Controller with 4 existing WAPS (they are also AIR-AP1832I-Z-K9). I now have a new AIR-AP1832I-Z-K9 which i need to add I've found so much info on Cisco/commands etc - i feel a bit swamped ...
There is a strange problem with our Windows 10 laptops in our environment. Windows 10 laptops will drop the connection when it moves from an AP in one WLC to another. If I move between AP's in the same WLC's it work with no issues. We have 802.1X set...
Hello, We have an external captive portal portal and our portal is hosted on AWS using load balancers. We also use Amazon S3 for static file hosting and other services from AWS that uses load balancers, so the IP addresses of these services are not s...
We have 2 wireless controllers( model : AIR-CT3504-K9) in HA. now its showing non redundant state as mentioned below:Can any body tell what could be be the reason? why maintenance cause says all ports are down. what does it means? now secondary is in...
Greetings all!I've spent about an hour researching this, and I think I have my answer already, but I just want some more assurance before advising my customer of anything. The scenario is that they are replacing a pair of 5508 controllers with a pair...
Hello, Is there any chance of using Cisco vWLC 8.5 without CMX and retrieve device/client location data to an external server?Basically we want to have an external server that receives data about users locations, etc.We found a "Server" configuration...
Good day,My query is as follows, which Access Point outside without contemplating the 1552, has standard to be used in a Gas and Oil Factory (intrinsic), or that has standard ATeX and CSA. Regards
I have the following problem, I have 2 WLC 5520 in HA, with Access Point 2702i and 2802E, of which the APs 2802E are always kept at the maximum power, and APs that are side by side are in the same channel, being much co-channel interference. The OS v...
1552H Mesh network (3 RAP, 13 MAP, 2504, Outdoor) dropped after 10 days working. Checked with WLC, 5GHz radio are down. RF2 LED of each RAP is off. Tried rebooting WLC and mesh was up for a while but drop again at the end. Only 3 RAP found in WLC.Cou...
I habe moblity express 1815 8.8.100 and one acces point 8.3.111 i would AP joind to controlleur i need to help
Hello,On Cisco WAP571, there is no SHA support and no AES support for SNMPv3 even on the last software version 1.1.0.3.Only MD5 and DES is available.When SHA and AES will be supported for SNMPv3 on Cisco Small Business wireless access points ?Thanks
