Hi ,
is it compatible to add A9K-4X100GE-TR to ASR 9006 with the following :
Cisco IOS XR Software, Version 5.3.3
ASR-9006-AC-V2A9K-RSP440-TRA9K-9006 FAN .......................(should it be A9K-9006 FAN V2 ?)PWR-3KW-AC-V2A9K-LC-FILRA9K-PEM-...
Hello Folks,
Trying to know if the BFD running over OSPF can detect the physical and line protocol up and bring up the OSPF immediately instead of using OSPF hello for link availability detection.
Ran a test in lab with ASR 9006 and ASR 9001 connect...
Hi All.
Currently one of my customers is replacing his infrasctructure for ASR9K, these routers are used as PE's, right after they were set on production, their memory raised to 60 to 70% of their utilization.
I've been reviewing this for the past we...
In all my implementations I had problem that XR (5.x.x, 6.0.x) would NOT announce routes learned from BGP ipv4 unicast neighbor to BGP IPv4 labeled-unicast neighbor.
Something like this:
https://learningnetwork.cisco.com/thread/117644
But now I am s...
Hello everybody. I have the ASR9001 IOS XR, Does it have an analog command #ip local policy route-map ? It is necessary to allocate locally generated control plane, but I do not know how to match it on iOS XR.
On ME3800x/3600 I use this syntax:
#ip ...
Hello,I have a question about XRv, it is necessary to specifically activate the service BNG?I installed Boot Image: /disk0/xrvr-os-mbi-5.2.0/mbixrvr-rp.vm Active Packages: disk0: xrvr-full-x-5.2.The image iosxrv-demo-5.2.0.vmdkBut there i...
Hi,
Suddenly one of my router(ASR 9K) was went down and came up. after that i have referred the log and it says that router got crashed due to the kernal crash.
can anyone help me that what could be the problem for kernal crash.
LOG File:
========...
So I'm trying to work with freeRADIUS and want to make checkrad work, it basically sends an SNMP get to some OID, upon further research I saw that it was using an old OID (OLD-CISCO-TS-MIB, 1.3.6.1.4.1.9.2.9.1) and this seems to be outdated so I want...
Hi Im working on asr9006 running RSP440 and XR 4.3.4, and after configuring and committing bgp neighbour and route-policy comnfig, the box complained with the errors below right after I committed the changes.The changes were accepted and the box is ...
When attempting to upgrade a 9000v from an ASR9010 host (5.3.3), I discovered that some of our ASR9K's have MPP configured on some interfaces, while others have none at all. Working with my test unit, I saw that I could configure MPP for all protoco...
Hi
I am not able to access my ASR 9010 even by telnet or ssh.(actually the authentication seems to be accepted but showing nothing)
even I failed when I tried to access it by console and I got the following logs:
Press RETURN to get started.
RP/0/R...
HI,
I am not able to configure the E-LMI in ASR 9000 router's.
AIRDCILABUS01(config)#ethAIRDCILABUS01(config)#ethernet lmi
^% Invalid input detected at '^' marker.
AIRDCILABUS01(config)#
Hi,
we did a stress test this morning on our IGW (ASR 9912; RP2; TH HW).
There are multiple eBGP sessions and we get full RT from them.
If we disable ISP1, it takes around 35 seconds to failover to ISP2. It takes a few seconds to tear down the BGP s...
