Hi All,I am trying to find out the maximum amount of flowspec prefixes that is supported by ASR9k, ASR9900, NCS55A1, and NCS57B.Please advise providing relevant links as I have been searching (Cisco community, release notes, implementation guides, ar...
Forum Posts
Hi Experts. Hardware: ASR9010 Software: 5.3.4 Customer want to configure Segment Routing MPLS and MPLS L3 VPN, we have Typhoon cards (MOD80 and MOD160). I would like to know whether MOD80 and MOD160 support SR MPLS and MPLS VPN function and whether n...
Hello,I have an issue where my A9K-MOD200-TR linecard notice that FABRIC-FIA-1-DATA_SB_SERDES_1_FAIL_0. Is it a critical Fault? Plaese help me.LOGS:RP/0/RP0/CPU0:ios#show plat summary location 0/9/CPU0Sat Jul 26 09:43:27.061 UTC----------------------...
================================================================================Location TEMPERATURE Value Crit Major Minor Minor Major Crit Sensor (deg C) (Lo) (Lo) (Lo) (Hi) (Hi) (Hi)---------...
Hii guys,Need your advices, My devices is cisco NCS5500 series with dual routing processors and will upgrade from version 7.x.x to 24.x.x. Can I upgrade from standby RP first, and then swing the RP? Or just upgrade the active RP one, then the backup ...
Hi, I'm trying to get statistics for interfaces in ios xr 7.9.21 64 bits (ASR9904) and 6.9.2 32 bits (ASR9001) in l2tranport mode through gnmi but I can't seem to find the right YANG module to query for this statisctics. I tried Cisco-IOS-XR-infra-st...
Hello Community, We are facing a critical issue on our Cisco N540X-16Z8Q2C-D router. One of the interfaces that was actively running a live service suddenly stopped working without any prior warning or configuration change. Details: Device Model: Cis...
Hello, I'm trying to configure BFD parameters under BGP, and while it allows me to configure timers I can't seem to find how to configure BFD fall-over on my peer. It does allow me to configure BFD fast-detect but I specifically need to enable fall-o...
Hi,I've set up this policu but got this error when applying it to by BGP neighbor :route-policy RP-TRACK-T5-LP-200if track track-T5 is up thenset local-preference 200passendifend-policyrouter bgp 65532neighbor 172.31.255.5 use neighbor-group RR-CLIEN...
HI ALL emergency help ！！！ncs5501 ALARM led how should i clear or fix this fault?
hi all my device is ncs5501 ,I would like to know how I can clear this error RP/0/RP0/CPU0:ios#show platformTue Feb 18 02:14:18.338 UTCNode Type State Config state----------------------------------------...
Well I am having a problem when triyng to connect to grpc from a directly connected network. The port is showing as close from the pc but i can connect to the grpc service from xr 2 device without a problem. I have tried with another interface with d...
Hello, I have a IOS-XRv 9000 with SSH and gRPC enabled, running on the latest version of CML2. gRPC works fine from a directly attached network, but I cannot get gRPC to work from a remote (non-local) network. Since other protocols like SSH work as...
Resolved! NCS540 - mpls,bvi,mtu
Hi all,I need some help, my head will explode I am moving out from asr920 to ncs540 (v24.3.2)On asr920 we had bunch of bdi interfaces facing customers subnets, firewalls etc. Together with it there were bunch of static routes exiting bdi interfaces. ...
Hi. I am setting up a N540X-16Z4G8Q2C-A router. I can setup users with passwords. I have setup users with keys on other Cisco switches, but this router is giving me errors. Does anyone know how to set up keys on this router?I get the following error ...
