Hi , What is SU and SD mean in the below output. I am seeing there is a mac flap between P015 and few interfaces.Po15 is down and when I see sh run config of that port channel no po15 , there is no configuration which means is it configured or n...
Forum Posts
(Bit of a newbie when it comes to 1000V. Apologies in advance if I'm using the wrong terminology.) I have two separate 1000V environments and both worked perfectly up until a few days ago. Now, however, one of them has stopping syncing up with vCente...
Resolved! Nexus 5020 licensing
Am I correct in saying that the N5000-AS is already included in the NX-OS and is free to use. Or do I need to install it? Or do I only need to install the additional ones such as N5020-SS after purchased.
Planning to upgrade our Cisco Catalyst 6807xl Sup6T VSS clusters 15.4 (1) SY2-> 15.5 (1) SY1 Can we do it with ISSU or eFSU to get as little interruption as possible? Finds no information about it when I go from 15.4 (1) SY2-> 15.5 (1) SY1
WS-C4500X-32SFP+ V06 is in rommon. I need to make it a standalone switch and no longer a VSS pair. This switch was once deployed as a VSS pair. It is going to be repurposed but as a standalone switch. Currently it is in rommon. How can I make it a st...
Hi NXOS Gurus.I'm planning upgrade to 7.1(4)N1(1) of the series of N5K switches running quite old images like mentioned in the tytle.reading the release notes to target version (https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/u...
Resolved! VPC status down NX 5k
Quick question. I'm adding some vpc ports to a switch which has vpc already configured on it. The fibers will run to a server. I've pre-configured the port-channel and interfaces. The fibers are plugged in to the switch but not yet to the server....
Resolved! Nexus 5596 upgrade
Hi All, I have a pair of Nexus 5596 running in vpc with old firmware( 5.1) and there are 8 fex connected to the N5K. Basically the N5K is only used for basic layer 2 function only (without FC). We are planning to upgrade the N5K to the version...
Hi, so I can get a better understanding of VXLAN/EVPN I am attempting to set this up in VIRL. I'm working from several example configurations, is this actually possible in the emulated platform? Reason I ask the basic question is that some key comm...
Hi ,I have Nexus 7706 chassis with N77-F348XP-23 cards.I can not find if it is Load Balancing Using Port Channels method with gtp-teid supported on F3 cards.i only found this guide https://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/nx-os/i...
Hello, I have a question regarding the connection of Nexus 9K (NXOS 7.0(3)I7(1) with fex Nexus 2K (System image: 7.0(3)I7(1)) connected to 6 Hosts with VMWare 6.5 Each Host is connected with 2 x 10 G Link to the Fex. For each host we have a port-chan...
Looking at the TMGMatrix compatibility tool I don't see the SFP-H25G-CU1M listed as being compatible with a N9348GC-FXP ....is there something I'm missing?
Hi guys, We have OTV implemented between 2 sites by N7Ks. Configuration: default vrf - eigrp routing, link between 2 sites configured "otv_map" vrf - ospf routing. In site X we have: extended vlan A, not extended vlan B and server VM1. In site Y we ...
I have a weird connectivity issue for the ports on a pair of NX9K, which seems like one way traffic problem. The setup is: NX7 --- NX7 - has HSRP gateway for the VLAN | \/ | | /\ | NX9 --- NX9 < VPC peer-link between | ...
Hi All , We have two data centers as shown in the picture. Data center 1 is primary and data center 2 is secondary. At each data center 1) Nexus 7ks have 3 VDC's configured . WAN_VDC is connected to Cisco ACI using L3 Port channel . note : At...
