Hi Team, Anyone has a battle card Cisco ACI Data Center Solution and Aruba Pensando with Aruba Fabric Composer? Thanks.Regards,Awan.
Hi Team, Anyone has a battle card Cisco ACI Data Center Solution and Aruba Pensando with Aruba Fabric Composer? Thanks.Regards,Awan.
I can't Create BOM Cisco Nexus 9808 with 2 supervisor but on 9804 can please help
Hi, I have got a customer request to build a greenfield 2 sites DCI using BGW back to back model, with 2 x N9K at each site. There is no other spine nor leaf purchased for this project so the 2 BGWs at each site will act as the leaf role. In this sce...
Hi,I have to enter the bootloader of some Nexus N9K-C93180YC-FX switches, cause at the moment they are using an aci image, but I have to change them to nx-os. I was connected via the serial connection and I have tried it with putty, tera term and sec...
I'm newly joined into the Cisco ACI world. We are planning to migrate from traditional to ACI infrastructure. In our environment, we have Palo Alto Firewall and we gonna integrate it as L4/L7 with one-arm mode. The service graph will be applied based...
Hi All,We are using Cisco 6513 switch in VSS and we are facing high CPU utilization from last one month. Most of the process used by OBFL. show processes, CPU sortedCPU utilization for five seconds: 60%/7%; one minute: 58%; five minutes: 60%PID Runti...
I connected FEX to Nexus 9k and after FEX went Online, I configured HIF.After saving with copy run start, I shut the fabric interface and took FEX offline.With the HIF gone from the running-config and FEX unrecognized, I did a copy run start.If I the...
Hi, We have successfully created a VXLAN Fabric using NDFC where we have external connectivity (eBGP) via the Spines (dual Spine / Border role) due to physical separation of WAN circuits to the Spine cabinets. Are there any downsides to implementing ...
Hello, We have been running into trouble with the first module in a N6K and are searching for a workaround. We want to add a module on a N6K-C6004-96Q. Using fixed (non removable) slots 3 to 4 requires a license (L-N6004-12Q-LIC) but what about slot ...
I konw the Nexus 7k or 9k can be used "show system internal l2fm l2dbg macdb address" to view mac move history or called it "mac updata records", as shown below: But the Nexus 5k is not support this command,because 5k used fwm isn't l2fm。In 5k,we onl...
can anyone tell me to how to check bgp alert in apic controller and how to configure a switchport in apic
Hello!We have a cisco Nexus7000 C7010 (10 Slot) Chassis ("Supervisor Module-2") Some abnormal alarms have been generated2023 Jun 30 17:10:36 TFL-J15-DC-N7K-002 Jun 30 17:10:35 %KERN-3-SYSTEM_MSG: [80498716.274526] end_request: I/O error, dev sdc, se...
N9K-9396PX(config)# hardware profile svi-and-si flex-stats-enableNot supported on this platform, or system not ready"" Nexus 9396PX not supported hardware profile svi-and-si flex-stats-enable.i need egrees SVI Counters to monitoring interface vlan.wh...
Hello,We have 2 Nexus 3180YC switches that are running NXOS version 9.3. We are trying to enable the private-vlan feature and the port-security feature. When we run the commands "show feature | i private-vlan" and "show feature | i port-security" it ...
I am using a Nexus 3k at version 9.3(10).I am trying to use the interface at 1G speed and the other end is connected to my linux server.I can see the status as xcvrSpeed .Eth1/1 -- xcvrSpeed 1 auto 1000 SFP-H10GB-CU3Mswitch(config-if)# show run int e...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-09-2024 04:42 PM | ||
08-30-2024 08:33 AM | ||
06-14-2024 06:10 AM | ||
06-12-2024 07:09 AM | ||
06-05-2024 03:06 AM |