Hello, I have a problem with a phone 8861 using a power injector, and this phone has a 8800 KEM module that is not power up. The power injertor is 802.3at AIR-PWRINJ6
Forum Posts
Hello allall cisco ipphones in our organization display the following error message "service interruption" , until now i still can'f find the cause of this issue, and the only solution that i found to make phones working is to change de "Device Secu...
Hi, I have a problem with IP address from which CUBE sends sip-option reasponse to remotely CUBE. On dial-peer which handles SIP calls towards remote SIP CUBE is configured: voice-class sip bind control source-interface Loopback1 voice-class sip bi...
Resolved! 8821 Phone Going Into Preservation Mode
We recently replaced our Cisco WLC and AP's with Meraki MR46's. Since doing this our 8821 phones will go into preservation mode ONLY on 3 of the 5 AP's. When you call into the phone you are able to establish the call on both ends. When the person wit...
with Raees Shaikh Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn tips on Installation, Upgrade, Configuration & Troubleshooting Cisco Unified SIP Proxy (CUSP) with Cisco Expert Raees Shaikh. Raees ...
a Pair 4331 Cube HA , where the standy sometimes reloads - and sometimes more than once , and during that , it effect our sip calls ( disconnecting ) I know its default behaviour when recovering HAreload reason : RG-application reload on voice-b2bh...
Hello guys,at a customer, we want to update the WLAN Settings on the 7925 phones via WLANDefault.xml. Last week i installed the xml file with Auto b/g. This week we wanted to change it to Auto-A. When i installed it, the phones downloaded the xml and...
Hi all, Beginner????? LOL! Strange problem: 7 server cucm cluster 12.5 su5 LDAP Al the subs in the clusters can reach the corporate directory from any Cisco phone except 2 subs. When I switch several 88xx and 78xx phones from those 2 servers to the o...
Hello,We have a call manager 10.5 and several MTP routers, We are needing to stop any call on each MTP router, reset the router and enable the router, to clear any MTP issues. We were told at one point by Cisco to login to the CUCM and uncheck the M...
Dear all,I have CME ver 12.8 on ISR4331 in which caller-id is not showing as stated in the debug attached it is failed to be received.I did a test by plug the fxo line to analog phone and did a test call in which the caller id appears on the analog p...
Resolved! cisco jabber invalid status code in response this may be caused by a configuration error in the idp
Hi All, We have implemented the SSO using the Microsoft ADFS in our cluster and some users have reported the below issue: After login with their windows credentials they are getting following error message: Invalid Status code in Response. this ...
I have a Cisco 7841 that was originally created as a 8861 so the requested phone load is incorrrect. Phone TypeProduct Type: Cisco 7841Device Protocol: SIPReal-time Device StatusRegistration: Registered with Cisco Unified Communications Manager Sanch...
Resolved! Block outbound call on MSTeams
Dear Friends,The MSTeam has integrated with CUCM 12.5. Both IP phone and Teams are ringing simultaneously for incoming calls and able to answer on both ends. The manager wants to block outgoing calls from Teams and only allow from the IP Phone. I hav...
Post upgrade, we have a number of 7940 phones that for some reason look like they switched to SIP firmware and are trying to auto-register? Tried factory resetting, but didn't help. The device protocol in CUCM is SCCP so not sure where these phones a...
Hello everyone,i've a CP-7841 i want to update the firmware with the CLI commands,i've also reset the phone but the system will not start we can see white screen start but no load the OS.
