Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello friends,I have one Cisco 2811, version IOS 12.4(15)X. I wrote: "show telephony service all", "show version" and "show ccm-manager", but 2811 didn´t show version CME.How can i know version CME throught CLI command or another form?Thanks for you ...
We are needing to obtain spare handsets for Cisco 7931G phones. How do we obtain replacement handsets for the 7931G phones? What is the part number for a replacement handset for the Cisco 7931G IP phone? Cisco has listed handset part numbers for othe...
I am calling to other cisco phone, other cisco phone has call forwarding on mobile. once the call forward to his mobile. Call should be charged his extenstion (in billing) but it is charging my ext in the billing ? management need billing report base...
Anyone have any idea how to reroute the PSTN call from 1 cluster to another cluster's vg (MGCP)?Phone A registered to Cluster A.VG B registered to Cluster B via MGCP.Cluster A & Cluster B is running as intercluster trunk without Gatekeeper.Is it poss...
Hi NetProI have two DN 500 and 502When number 500 is busy or no answer the call going to 502, setup CFnA and CFB and works OK.When number 502 is busy or no answer the call going to 500, setup CFnA and CFB and works OK.But when the 502 going to lunc...
Hi everyone, So I ran into a problem in which I have hit an absolute dead end. I will list it first, then I will follow it up with various methods I attempted to solve it. The phone in question is a 7931G, I can't tell you what boot software it tries...
Hello,I'm trying to install the CUPM 8.7 evaluation.At first i got error during installation: Postgres install failed saw no error code ( on 2 seperate machines same error )Then i installed Postgres manual with the file that the installation saved in...
I am using IP Communicator 8.6.1.0 and I can hear the audio just fine through my headphones, but when I try to play other audio, like from a webpage, the audio goes through my laptop speakers instead of my headphones. This happens even when I'm not ...
One of our users is stating when she runs reports for Total Outbound Calls for her agents they are not showing up in the reports. She also states that the agents are logging out and making the calls. Don't the agents have to be logged in for the ca...
Hello All, I have a situation where calls that are forwarde back out to the SIP PSTN are being rejected because the calling number is not recognized. 1). Phone A on PSTN calls Phone B which is on an Avaya CS1000M PBX.2). Cisco Voice Gateway ter...
Any thoughts on the best way to get from Unrestricted to Restricted? My inactive partition is 8.6.2.20000-2 restricted, so I know I can roll back to it then apply the restricted version as an upgrade. My issue is that a large number of changes have...
Hi guys!I have a customer with the follow problem:Customer environment has analog PBX, CallManager and MGCP gateway 8.5.When he makes an international call to Argentina, from an analog phone the call goes through the PBX, then goes to the MGCP gatewa...
Hi everyone.. Iam new to this community. I have a doubt which Iam not able to clear about call preserve in MGCP and H.323.In Gatekeepers and Gateways text book I read that "MGCP supports call survivability for analog and T1 CAS calls, and MGCP does n...
Dear All,I have 2801 router. Under voice-card 0, I can't have "dspfarm" command. Only "dsp services dspfarm" command it takes. When I tried to bring up voice channnels on T1 controller it gives me error message insufficient resources. I want to use t...
| User | Count |
|---|---|
| 4 | |
| 3 | |
| 2 | |
| 2 | |
| 2 |
