cmterm-7911_7906-sccp.9-1-1SR1.zip
cmterm-7911_7906-sccp.9-1-1SR1.zip
"is this okay to remove the phone files from flash which aren't related to my cisco lab setup?"Reason(s): 1-All phones i've are 7961 series. 2-CME 7.0.0.1 which i'm using contains files for 7906-7911,7914,7920,7921,7931,7937,7940-7960,7942-7962,7945-...
There's a question https://supportforums.cisco.com/thread/2157114?tstart=30 where the poster has a problem firmware upgrading a phone. Doing a factory reset (123....) forces the phone to upgrade, but it still has problems.I'm guessing a CME config er...
Hello Folks , we have two trunk one is sip and anther one is pstn , my voice mail is in some third country and that is routed through SIP , now my requirent is if some body call at my extension from PSTN , it should 8-9 ring then disconnect...
Hi All,I just would like to have some expert opinion on the probability of using IVR through Unity Express and then calls should route to Call Manager.For example, If we have a Site with 2800/2900 ISR Router with Unity Express Module NME-CUE and Cisc...
Hi all,I am trying to upgrade the firmware on a 7945. I've done the steps like every other phone type I have, of copying all files to flash, tftp-server flashing them, going to telephony-service and "load 7945 SCCPxyz", but when I reset the phone, it...
In my lab setup have two seperate 1760 CME 4.1 routers serially WAN'd to a 2620XM router using RIP, that has the Unity Express NM-CUE 3.1.1 module in it. The 2620 is just doing the voicemail and routing between the two CME's, no ca...
Hi after upgrading the callmanager from 7.1 to 8.0.3 i found extension mobility not working. I was told i had been hit by bug CSCsy76489 by cisco tac. I cant find any information on this particular bug on the tool kit since its still internal. I wond...
HiI have spent 2 days behind this little issue and still cannot figure out the catch. I have CISCO3825 with IOS c3825-adventerprisek9-mz.151-4.M4.bin and cme-bacd-3.0.0.2. I just need AA and no need for hunt group. here is the config:dial-peer voice ...
Hi All,Is it possible to do fax over IP which topology below?Fax <<>> VG+transcoder <<<<<H323 G729>>>>>> 3rdParty PBX <<>> FaxBR WINAI
Hi,We are facing a problem in our production CUCM 6.After the power shutdown neither the Pub or Sub is doesn't work the Pub is asking for recovery disk "which is not available in our stock".And the Sub is running but I couldn't access the cm administ...
I have installed an AQM version 2.6 with CUCM 7 and UCCX 7.I have followed the instalation guide but I have some problems, I had some logs from Event viewer but I haven't found any information to fix them.Logs:RecordServer: The description for Event ...
Hi, i want to see whats the easiest solution to generate a call report from a cisco telephony. I was trying to generate it from the cli, but i just cant fin the way to do it.I will apreciate your answers.
Does anyone know how to find the manufacture date of a Cisco IP phone based on its MAC address of Serial number? Is it the same as with routers & switches?
Hi,I am facing issue with my cisco unity module (NME-CUE). My router (2911) rebooted accidently and it boot with the IOS 15.2. after that my voice mail system gone down. In 15.2 it is not taking command for integrated service engine. Now I have reloa...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-26-2025 05:48 AM | ||
04-24-2025 02:49 PM | ||
04-15-2025 02:12 PM | ||
04-15-2025 10:57 AM | ||
04-15-2025 03:40 AM |
User | Count |
---|---|
3 | |
2 | |
1 | |
1 | |
1 |