Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi all,i have server with CCM 3.3(5) and O/S 2000.2.7, i would like to take a backup data for it and restore this data in another server with win 2000.4.3a and CCM 3.3(5) then after that i will upgrade it to CCM 4.2(3).does this process will success...
we have configured a hunt pilot number for our helpdesk number which works great however we want to be able to easly forward the hunt pilot number to voicemail after hours with out hunting through the list first - directly to voicemail. i want all us...
I've just converted a customer to an MGCP PRI. Everything is working fine except for international calling. I'm getting this disconnect code on the gateway using a Q931 debug.Cause i = 0x829F - Normal, unspecifiedWhat does this mean? Users get a b...
I'm trying to understand the capabilities of this card, and am lacking in some knowledge of the telephony aspect.If the T1 I present to this card has PRI signaling, can the D&I functionality allow me to hand, say, half the channels to an otherwise vo...
Hi,I'm trying to upgrade an existing MCS7835 to an MCS7845 without having to rebuild it. Adding the extra processor works fine, however, the full spec requires 4 72gb drive (rather 2x72gb for 7835) and I was wondering if its ok to manually configure...
I have installed the callmanger 5.1; and installed the DLU as well but i cannot activate the callmanager service ...
Hi, I have a current issue in our office where if we do a conference call, it'll only allow 6 callers to attend the call. The procedure we use is very basic. Dial 1st person, press more, press conf button, Dial 2nd person, press more, press conf bu...
Hi, I have a Call Manager cluster which is having a trunk to another Cluster. I am going to put a firewall between these two clusters. Can anyone tell me what all ports need to be opened on the firewall to maintain this trunk. If the firewall is in...
Hi,I want to configure two sip trunks on CME 4.1. One for SIP telephony provider, and the other for sip gsm gateway on the same CME. Any suggestions or configuration examples?Thanks and best regardsRupnik
Hello,I have a number of questions regarding using the 7970 IP Phone with PoE. Firstly, I have an IEEE 802.3af power injector that isn't a Cisco brand. It is 48v and I'm wondering if I can use that with the phone, though I understand this is probably...
Hi,after upgrading from 4.2(1) to 4.2(3)SR2B we have the issue that occasional when we pick-up a call we have one-way voice idenpendent if the call is off-net or on-net.any ideas for troubleshooting?many thanksRainer MangelsdorfSenior System Engineer
I have CCME 4.1 with 7906G Phones (over WAN)7906G firmware is jar11sccp.8-0-2-25.sbnAfter power loss 7906 does'nt startsaying;"downloading term06.default"I cannot access the telephone anymore.
Avaya recommends marking call control traffic the same as voice traffic, COS=5 and DSCP=46, and therefore putting call control traffic in the same priority queue with voice during congestion.The rational is that call control and inter-IPSI traffic is...
I need to set up a CUE script in where the caller can dial by extension at any time during the opening greeting. I've tried to configured but it drops the call as soon as I dial the first digit of the extension i want to reach. Can some shed some l...
Hello guys, do you know if it's possible to change the hostname of a callmanager 5.X through GUI or CLI ? Is the hostname still linked to the database as in 3/4.X version ?Thanks a lot.Julien
