Hi All. Hoping that you can help. CCNA exam, on the CLI, I am able to use short hand cmds i.e. conf t, copy run start, sh ip int brief or do the cmds have to be full i.e configure terminal etc? When saving the config can use wr or does it have to be ...
Forum Posts
Anyone have any insight into identifying the correct snmp oid for a C9500-48Y4C stack running 16.12.3?usual cpu snmp oid of 1.3.6.1.4.1.9.9.109.1.1.1.1.5.1 yields no such instance.Documentation points to an oid of .1.3.6.1.4.1.9.9.109.1.1.1.1.25 for ...
Hi Cisco team,I have one problem with netflow traffic that not established connect udp port 2055 to my nexus 7706 CoreSwitchHere is command on CoreSwitch=======================flow exporter TT-NETFlow-Exporterdescription TURBOTECH NETFlow Exporterdes...
hi does anyone know what does evalrighttouse license mean i don't know what it is and i can't find anything about on cisco all i know is when you purchase a license it goes to right to use and if you haven't bought a license it is eval that means you...
When I tried to upgrade from asr1002x-universalk9.03.16.06.S.155-3.S6-ext.SPA.bin to asr1000-universalk9.16.09.05.SPA.bin version, I used "boot system bootflash:" command, but when the device reboot it didn't do it. These are the output when the devi...
Resolved! ENCOR Exam Topics Clarification
6.7 Compare agent vs. agentless orchestration tools, such as Chef, Puppet, Ansible, and SaltStack When the exam topics says "compare," do we need to know how to configure the orchestration tools, as well? Any input is appreciated. Jason
We have a few ISR 4000 series routers which need to be monitored using SNMP by a third-party NMS server. The NMS monitors Interface status and Bandwidth utilization by default but requires MIBs to be uploaded for monitoring the other components and I...
Hi the thing I want to achieve is to have a unencrypted VPN tunnel between two RV345 routers running the latest firmware (there is no CLI support for this router) The configuration I did so far is in one of the routers I entered an IP for the tunnel ...
HiI have this scenarioI have two VLANs 192.168.123.0 and 192.168.122.0 one cable running from the router to a managed TP-Link T1600G-52TS switch from this switch cables are running to multiple rooms in one room there is only one cable and one hardwar...
Hi guys.Today I got a request to insert an equipment to our monitoring system.The customer already has its monitoring system with its configuration.Since I only manage the WAN, I would like to make polling and also get traps for only a specific BGP p...
Hey everyone, I'm trying to configure SNMPv3 on a switch to send specific traps to a SNMP manager in this case Solarwinds. I need to collect the following information:CPU, energywise info, interface status (up, down), temp, trending for related data,...
Hi,We have a Cisco Prime 3.xWe would like to insert dynamic custom text into a subject or body of alarm email. For exampleHost: $hostname , interface : $interface_name , Line ID : $interface_description I did find any description about the custom tex...
I have been searching everywhere on the internet to find the answer, but nothing worked. I need to host a server, but the only step I'm missing is enabling the DMZ and i don't know where and how to login into the routers page. I logged into the first...
hi everyone. i'm using parrot sec os. i installed packet tracer 7.2.1. after installation is done, i entered "pakcettracer" in terminal. it displayed "starting packettracer 7.2.1". but it wasn't. what should i do ?
Hello I have a problem with the sending of reports by mail when it arrives lack of the upper part just the curves are displayed thanks in advance
