I want to Configure 2 Serial Port of 2 Mbps link on WIC-2T card on 1721 Cisco router and wanted to get Output as 4 Mbps as uplink and Morever pls suggest how to make this multipoint to single point
I want to Configure 2 Serial Port of 2 Mbps link on WIC-2T card on 1721 Cisco router and wanted to get Output as 4 Mbps as uplink and Morever pls suggest how to make this multipoint to single point
Hi, We have an existing 1700 IOS security router with existing site-to-site VPN parameters configured(running config attached). Im planning to add a remote access IPSec vpn configuration on the router to provide access to remote users using cisco vpn...
Hi All,followed the procedure on the page below, but, when rebooting, still get prompted for a password. I'm wanting to set the switch to no secret and no password. Can it be done like this..? Little unsure as to why this won't work. Cheers.http://ww...
I found a reference to Firmware v2.01. However, I can't seem to locate that version inthe downloads. Does anyone have any info orperhaps a link? TIA....
Port security with a single MAC has been enabled on all my switch ports. Recently, I've had some users complaining of being disconnected. I checked and found that the users' ports have all been err-disabled and the users all had 2 MAC addresses on th...
Hi,I have 2 2950 switches. I need to configure etherchannel to increase bandwidth between the switches. I have set ports 1 and 2 on each switch to trunk mode and using 'switchport mode trunk' and then put them into a channel group by 'channel-group 1...
Hi All,I can't delete an old .bin file from the flash dir,switch: delete c2950-i6q4l2-mz.121-6.EA2c.binAre you sure you want to delete "c2950-i6q4l2-mz.121-6.EA2c.bin" (y/n)?yFile "c2950-i6q4l2-mz.121-6.EA2c.bin" not deleted -- permission deniedWhy w...
In regards to Eigrp the doucumentation indicates that a router will make a route a feasible successor and add it to its topology table if the route's reported distance to a specific network is less than the feasible distance of the current router.My ...
I am replacing a 1602 Router with a 1721. Can I use the WIC-1DSU-1T to replace my 4 wire 56k integrated interface?
I have been tasked with the redesign of a Wide Area Network for my customer.The current network is configured as follows: 3 Main hub locations 7206 VXR routers that are all connected to each other via Frame Relay T1. This is the main Network Backbo...
Hi, we're having a ds3 installed and the provider indicates that it will run on coax. The NM-1T3/E3 card also has bnc connectors. Is coax the typical media? I was expecting maybe fiber or even Cat5.thanks,
I have two T1s between two routers in a PPP Multilink group. Everything seems to be working fine but routing for this multilink subnet seems odd. Maybe it's just a multilink thing. Anyway, I have this link set up with a 24 bit mask 172.25.155.1/24 ...
Hello all,Cisco recommends configuring VPN with IPSEC/GRE combinations.Does CEF works in such configuration? Can IP switching, QOS classifying, GRE encapsulation, encryption (HW or SW) and QOS congestion management be done in a single interrupt? My h...
I have 4 layer 3 switches (2 x SW6509 and 2 x SW3750) interconnected in mesh. I receive a request to remove the EIGRP, which is the routing protocol for all swicthes for layer 3. The way the switche were set up was in case one or 3 of them goes down ...
Hi AllI am using a 7206 as BRAS to terminate ADSL customers. I then switch th ePCS in thru an 8510 MSR towards DSLAMs.I am using CTTR to police ingress PVCs but would want to shape egress towards DSLAMS of a local provider how is is done on CAT8510. ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM | ||
11-08-2023 03:38 AM |