Other Network Architecture Subjects

why 4506 doesn't pou up the common message,such as "switch port up/down,line protocol up/down"? Pls be notice I have config the switch to "logging on,logging console level debug", This switch IOS version was 12.1.14.E1

I was wondering if you could help me out with something I am working onhere. I have on my LAN, 2 VLANs (VLAN10 and VLAN192). My corporate servers are on VLAN192 and corporate users are on VLAN10 I have here atthe corporate office a 2611XM router w...

Replacing and old RAS box with a 2620 router and NM-8AM module solution. I have followed the sample configuration at http://www.cisco.com/en/US/products/hw/modules/ps2797/products_configuration_example09186a00800e0dcd.shtml, but when trying to test w...

I can't ping or telnet to the remote router. The interface on thelocal router is s1/0:0.102 and shows the line up. The router has beenpower cycled many times and still the issue persists. I do not haveaccess to the remote router. Is there anythin...

Hi All,Can any body tell me the function of minCIR in frame-relay? I had found some doc and the doc just explain in as "mininum CIR". I can not get the meaning. Thank You!Waimen

We have a Frame-relay link to remote location and users are complaining about slow performance. While looking into serial interface detail I found that the "output buffers swapped out" counter is keep increasing. Any one can help me to understand the...

I have a Router mc 3810 and i dont have the boot helper image (mc3810-wboot-mz.bin), how can do to find it??? Please HELP!!!Router(boot)#sh verCisco Internetwork Operating System SoftwareIOS (tm) MC3810 Software (MC3810-WBOOT-M), Version 12.0(7r)XK, ...

I have 3 Catalyst 3500's on one IP subnet. All users on the switches are in the default VLAN1. I am in need of another switch and am being sent a 3com by headquarters. My question is this: How will the Cataylst switches and the 3com work together? Wi...

Has anyone run into this problem?I experienced very slow response time from Cisco Works or Real Time when I have to go through the PIX firewall to the servers via the web interfaces. If I’m on the same LAN its fast, otherwise it seems to take the men...

I I have about 10 2924 switch’s and two cat 4006 box’s I have also set up 10 Vlans that each switch is dedicated to, all the switch’s are connected physically back to a WS-x4124FX switching module in the 4006 and they are all trunked using dot1q. My...

Dear allI have a Router 1710 which having a VPN function and connected to IAS RADIUS server. Do you have any tools to view who connecting to the VPN? I don't want using the CLI on the router to check it. ThanksRegardsGodwin

Hi,Can anyone tell me whether Channelised E1(Leased line) and Channelised E1(PRI) work on Time division Multiplexing scheme?Regards

hello,i have a 2950 switch with enhanced ios image.it seems like again we have only input rate-limit ... via service-policy input name .... and no ... output.all the docs i've read states egress side doesn't have policing function.is there a way to l...

I'm looking for isolation suggestions or solutions. I have a 7513 using a VIP2 connected to a 2600 router. It appears that MPPP is not load balancing correctly. The ratio is between 10:1 and 20:1 on the output of the 7513 toward the 2600. The 7513 is...

I want to have 2 ip helper-address commands, but I want to be able to have the first DHCP I list be the primary and the other one only used if the primary fails. Is there any way to do this?Thanks,John Singer