Other Network Architecture Subjects

Cisco Catalyst 2924-XL switch, STP supports 64 vlans. What happens when another vlan, say 65, is assigned? Does the 65th vlan operate with out STP? What are some of the issues I need to plan for? Thanks in advance - I don't have a switch to test this...

HiI have the following scenario :Router A is connected through a Frame Relay PVC to a private IP backbone running BGP.Router B is also connected to this private IP backbone. Router A can see router C user LAN through EBGP and vice-versa.Router A is ...

A quick and probably easy question but I have a standard class C private network with static IP's(192.168.12.xxx) of which I have a Cisco 3620 router to allow access from outsite sources. What I have is my network has used up my range and I am out of...

Hi guys,trying to bring up an ISDN interface at 7am and downing it at 7pm everyday. The router is a 2503. We dont want to use interesting traffic to bring up and down the interface (business reasons).Anyone got any ideas as to how this could be achi...

helloi can't find the exactly definition of one switch's caracteristic , that is: transfert rate.for exemple : for the catalyst 2950, we find that it has a backplane of 8,8Gbpsand a transfert rate of : 1,8Mpps (12 ports) ...

Using ospf can I get all internal traffic to use only one of the 2 backbones and all traffic headed out to the internet to only use the other backbone ?Each backbone is connected to my routers. I know I can set the cost for incoming traffic.

I have an external router 7206. I need to connect a dedicated router to it. The dedicated router is in my place but does not belong to us and directly connect to T1 to a specific site. I am using 7206 router to NAT instead of using my firewall. The ...

When the CSU/DSU on the frame-relay side resets the connection does not come back up. The ATM side shows it up but I cannot pass layer 3 traffic. After a shut/no shut on the ATM it comes right back up and passes traffic.Are their any config setting...

FriendsI am maintaining a good number of sites running on OSPF. Recently I have started facing strange problem. My one of the site has got 2 x 2 mbps links. Earleir my both links were working fine . Nowadays one of the link I can't ping from the rout...

Most of the time recently, upload is higher compare to download traffic in my cisco 2610 router connected to 3640 at speed of 64kb e1.Even if ethernet load was disconnected, it remains high.Could any body help me to solve this problem.

Does anybody know if a 2950C works fine if connected by 2 100TX in etherchannel with an Avaya Cajun ?ThanksRenato

I have a 2600 router and 2 networks: 192.168.1.0 & 172.16.1.0. I want to set up a NAT between them. I have configured the 192.168.1.0 as the outside and the 172.16.1.0 as the inside. I have set up my access list and my pool and my source list. Everyt...

Can you help me with a CAR problem. I am running ISL on sub ints of a 3620 & am trying to limit the bandwidth used by each vlan. I have applied CAR input and output on the subints as follows:interface FastEthernet0/0.3 description Customer3 encapsula...

The following problem ocurred to me recently. I have a Cisco 7500 with a subinterface whose IP address is 10.10.177.100/16 ( a whole B network is defined for the subinterface ). Then, I try to define another subinterface whose IP address is 10.10.10....

Hi AllI have many dialer profiles bound to a BRI int, how would I prioritize which dialer profile gets service? ...also if the bri was in use and a call came in on a dialer profile that had a higher priority, would it cut off the call on the dialer p...