I am trying to fix a non-operational, first deployment of a profile 14 mVPN configuration running on 3 PE routers connected in a triangle. All PEs run IOS-XR 7.10.2, and each PE is configured as anycast RP for PIM ASM in the MCAST VRF ("rp-address x...
I tried to connect my new delink router from other primary delink router for WIFI only. Can someone explain step by step for configuration
Hi everyone.. i have been looking through multiple posts on the forum for similar cases but have not found the answer Im looking for.. I've been primarily using this thread for guidance. https://community.cisco.com/t5/networking-knowledge-base/settin...
Hello, I have used Cisco 1921, and we forgot its login and password. I am trying to go into rommode for password recovery but am not able to. During router boot-up process I am using special command > Break to force rommode , router shows " Readonly...
Hello im a beginner in using cisco so my task is admin can ping admin but student cant ping admin.student1(198.140.70.4 255.255.255.248) and student 2 (198.140.70.11 255.255.255.248)admin1(198.140.70.3 255.255.255.248 ) and admin2(198.140.70.10 255.2...
When you do a show ip route, what does the "traffice share count 1" mean?sa26#sh ip route 174.0.0.1Routing entry for 174.0.0.1/32 Known via "ospf 2020", distance 110, metric 12, type intra area Last update from 10.0.3.250 on FastEthernet0/0, 00:38:...
We have a Cisco ASR1001-X and it can only pass 750 megs of traffic thru it on a 10 Gig circuit. I looked at licensing levels and they seem correct. Anyone have any ideas of what I can look at? Both Lan and Wan interfaces are 10 gig and Wan is using S...
Hi I'm trying to extended a L2 segment using MPLS L2vpn over GRE. I am able to establish the tunnel and get ospf and mpls adjacency also the xconnect between the peer is up but my 2 test pc cant reach each other. This is my PE3 config.interface Gigab...
Hello, I am working on collecting BGP-LS SAFI using BMP towards Cisco's opensource project Jalapeno. I have captured packets between RR and Jalapeno on each use case to observer where we see BGP-LS and where we DON'T see BGP-LS packets. few use cases...
I am using a 3750 switch and going through a Sidewinder G2 firewall. Thefirewall only has its startup config on it with and Internal IP address (.1)which will be the internal gateway. My switch has VLAN2 config of .2. I can ping from my switch to the...
I have an ISR4431 router, and related setting:ip access-list standard toGCP10 permit 10.136.0.0 0.0.127.25520 permit 10.136.128.0 0.0.127.25530 permit 128.231.0.0 0.0.31.25540 permit 128.231.32.0 0.0.31.255!route-map toGCPmatch ip address toGCP!route...
Facing issue with VRRP, when upstream router5 initiate traffic for downstream router6 then return traffic is not following VRRP VIP as Gateway. In my case switch2 is master and switch3 is standby.If Router6 initiate the traffic then VRRP working fine...
Hi Guys a quick one, I have a problem with my router which is not saving configuration after I switch off. Where do I go ? Any clues
Packets received by the router from BGP enter via a serial interface at 209.165.201.10. Each route is present within the routing table. Which interface is used to forward traffic with a destination IP of 10.10 10 24?People are saying that the answer ...
Hello, I built using the packet tracer a simple topology of three routers with ospf routing. I created a tunnel between the two routers that are not physically connected to each other, but I can't ping between one end and the other. I managed to ping...
