HI all:I had a successfull eBGP connection between all the peers.R1-1 is a router and ISP4 is a NX-OS,enviroment GNS3.As test i tried to connect R1-1 and ISP4 trough loopback interfaces(i know is not usual on eBGP,but it was just to test some load ba...
Hi All.I'm trying to get BFD enabled for VDSL connection, currently using Cisco 8300 with NIM-VAB-A card where we're terminated a VDSL connection.I have tried the following but the router doesn't see any BFD interfaces set up??interface Ethernet0/1/0...
Hi,I have a cellular router (IR809G) with a tunnel setup. I'm trying to view a multicast video over that tunnel. It does appear but the video quality is very poor. I'm in a great reception area and speed tests from the router into the network hover a...
Dear Expert,I have created LAB in eve ng and the same design is attached herewith.I have done all configuration with using MPLS WAN solution on design.Private NW is done successfully and now i wanted to allow all DC Server, HQ Users and Branch user c...
Hello.--- (obfuscated)2951#ping 172.16.8.7Sending 5, 100-byte ICMP Echos to 172.16.8.7, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms2951#traceroute 172.16.8.7Tracing the route to 172.16.8.7VRF info: (...
Hi Team ,I am looking for a Router that can support around 5000 users.. I am having 1 Gbps Leased line Internet connection and i want to provide internet for my users using Wi-Fi.. I will increase the Bandwidth as per my requirement, also i want to k...
Am I right in thinking the minimum config to get an MPLS L3 VPN up and running is:1) OSPF or another routing protocol in the provider network, including a loopback address (let's say Lo0). Not required on PE-CE interfaces.2) MP-BGP between PE's, usua...
Hello, I have a customer who has purchased two ISR 4331 router bundles which include the UC software license. The show license command shows that these licenses are installed on the routers but no corresponding licenses were added to the customer Sma...
Hi, I want to configure IPv4 vrf based iBGP peering between CE router to another CE router to forward only specific client traffic via MW path to the aggregation.
Hello Guys,I'm looking for Cisco vulnerability patches, what I can see is links that redirected to pages with huge content. For example if I have below links which cisco devices are vulnerable with software. I read and analyzed but i didn't follow ex...
Hi, I have configured a bridge domain between two ports of router (Gi 0/1 and Gi 0/2) and also i have configured a BDI interface and assigned an IP address (192.168.1.1/24) to it. In the picture below, you can see my topology. my problem is, the two...
Hi all, I wonder if someone knows why I get the error:MCAST-RR(config-router)#address-family l2vpn evpn% BGP: Error initializing topologywhen I try to configure address-family l2vpn evpn in the BGP process. The router has hardly any config and I foun...
Hi FreindsCan OSPF be accessed without Area 0 , what is the Technical Reason of Area 0 Besides its the Backbone of the OSPF Routing Domain? Thanks
Hi I'm building a dual ISP failover config, which I believe I have got sorted out (second to-be-primary ISP isn't online yet to test, but the "ip sla" etc stuff is using the correct failback route). Where I'm a bit confused is how to handle static NA...
Assume I have a 172.16.0.0/16 network, it is then Nated to a 192.168.1.0/24 network.This 192.168.1.0/24 is then NAT via a firewall to a public ip so that there is internet access.So being a routing issue, how can I route to the 172.16.0.0/16 network....
