I'm very new to Cisco and am trying to learn how to use it to finish a course that I'm running out of time for. I'm studying online and cannot contact any of my teachers or help, so I've come here begging for some assistance.I've been asked to config...
Greetings Can I see the mac address in an l2vpn xconnect? This is the way I have configured the l2vpn: interface GigabitEthernet0/0/0/3.10 l2transportencapsulation dot1q 10rewrite ingress tag pop 1 symmetricmtu 1560l2vpnrouter-id 100.100.100.100xco...
Hi,I have met a strange behavior of AD routing on ASR9k router.I have two same routes. The first route by config static route and has AD 1 by default and the second route is learned via iBGP with AD 200.The first route will be active with a smaller A...
Hi, I am working to deploy cisco router to one of my project. Please help/suggest me to choose a model that meet below specification- Minimun specification requirement as below- 1U Chassis Rack Mountable. The Router should have minimum 4x 1 Gigabit...
Hello, everyone!I've just started my MPLS L3 VPN studies and I am very confused about the RD and RT concept.To get straight to the point, why is there the need for both of them? If, for example, the RT identifies which VRF the route should be importe...
I have inserted SFP-10G-SR to port te0/0/3 on ASR-920-4SZ and found that it shuts down the port automatically. This ASR 920 has 1 gig license. does it mean that this sfp is not compatible? IDPROM for transceiver TenGigabitEthernet0/0/3:Descripti...
HI all.I want to use IP SLA source-interface as Loopback 0 R1's config ip sla 1icmp-echo 2.2.2.2 source-interface loopback 0 !ip sla schedule 1 life forever start now!track 1 ip sla 1 reachability !ip route 2.2.2.2 255.255.255.255 192.168.1.2 trac...
Hello,I've built very simple topology in GNS with Layer 3 Switches.Static Routing is configured on IOU1 and IOU3 IOU1[12.0.0.1]----[12.0.0.2] IOU2 [23.0.0.2]------[23.0.0.3] IOU3 If I configure ports as Layer3 ( no switchport) then I am able to pin...
Hi,I have configured a small topology with 2 x RTRs and 2 x SWs and have 2 ISPs and have configured HSRP for failover. I have connected ISP 1 to RTR 1 and ISP 2 to RTR 2, now vlan 10(ISP 1) that is for ISP 1 is working perfectly fine in SW 1 while n...
Hi all! I am doing a test on my EVE-NG, the original command in the OSPF is redistribute eigrp 100001 subnets route-map 123When I want to disable that command, the system tells me % OSPF supports only classless redistribution, keyword 'subnets' can ...
Hello all, I wanted ask the differences between the following versions and which one I need to allow me to be able generate crypto keys and be able to ssh and provide other security features as well? - c1841-adventerprisek9-mz.151-4.m10.bin- c1841-br...
Hello.Regarding a site-to-site tunnel with local ASA 5525, how do I advertise the tunnel remote subnet 172.16.10.0/24 to my EIGRP local LAN? 1. (there are no interfaces with this subnet so Vanilla EIGRP doesnt work.) 2. Redistributing static route gi...
Hello, I was trying trying the throughout of the ASR-920-4SZ router. This router supports Cisco ASR920 Series - 2GE and 4-10GE. We bought the 10G licensing and we are planning on upgrading our internet circuit to 10Gb/s. Does this this router need ...
Hello, everyone!I have this topology here, everyone is running OSPF. I am studying basic MPLS so I am still figuring out how things works. Only the routers on the right (P2 and PE2) are running MPLS and LDP. My question is, why is P2 telling PE2 tha...
Hello folks.How could I send output from the show command directly to an SCP server? Currently the redirect and tee commands do not support this type of export. Therefore, I am asking the community for help.
