As my exam is in 3 days its vital we find out how to fix thisSo basicly when we configure a router and Reboot it, it will erase everything and yes we did copy run startWhen we first got one of the routers we did a “fix” because it was password protec...
Forum Posts
Hi!I would like to try in trial virtual router CISCO CSR 1000V and I would like to install it on GNS3.First I would like to create a virtual machine with windows server 2022 and this virtual machine must be connected with cisco csr1000v router.My que...
Resolved! MPLS LDP Session Establishment failed
Hello, i have tried to connect an ASR1004(RP2,ESP20,SIP10) and a C6504E(VS-S720-10G) over 10G direct links. 10G port on C6504E is located on a WS-X6708-10GE ( with WS-F6700-DFC3C) linecard. Both interfaces are MPLS enabled via mpls ip IP connectivity...
Hi Guys, I'm relatively new to this and I've been researching lately but can't figure out how to properly do this and I have a Cisco Catalyst 3650. I have other vlans but I only want to access/reach the 100 and 200 (below):1. vlan 100 [workstations]1...
Hi All,when i tried configure Cisco ISR 4331 Router it hanged 2 twice and i restart it, after restart, Router Booting with image ISR Software (X86_64_LINUX_IOSD-UCMK9-M), Version 16.9.2, RELEASE SOFTWARE (fc1). Instead of ISR Software (X86_64_LINUX_I...
Can you help with this lab?Configure Sw1:• Enable DNCP Snooping for VLAN 10• Disable DHCP Option-82 data insertion• Enable DHCP Snooping MAC address verification• Enable trusted interfaces
Hi guys, i have a question for you. If it's possible of course. I have some problems setting BGP in ipv6 environment. I have this sample configurationRouter:1conf tipv6 unicast routingrouter bgp 1bgp router id 192.168.0.1neighbor 2::2 update-source l...
Resolved! Cisco Modeling Labs - CAT9300
Hello, I have been playing around with both CAT9300V models in CML. I am trying to create a L3 port and setup eigrp neighbor between an IOSv device. when I create the L3 port I see the port in an UP UP state but I can not ping across to the othe...
I'm trying to configure IPSEC on a new ISR C1111-4P but showing an error when I try to execute the command.crypto isakmp policy so either the syntax has changed with the new XE IOS or is a license problem? how I can tell? Here is the version output a...
hi how do you create stub router using packet tracer version 8.2.1I have tried this command but did not workR2(config-router)#eigrp stub^% Invalid input detected at '^' marker.
Hello Again, I ask the question.I did a lab configuration on the Cisco provided site, and there was no abnormality in the ping test between the hosts.However, if you perform a ping test on the leaf device, a time out occurs.Q. The figure above shows ...
Hi,I have designed a Carrier board based on cisco’s ESR6300 module and we are facing issues regarding LAN and WAN coming up time after IOS-XE boots up.After powering on the ESR6300 Carrier board and after IOS-XE is booted up we ran command show run...
Hello experts, I have a topology like below: Three routers R1, R2, R3 are running DMVPN phase 1. And I configure by static mapping, like below: I attach my eve-ng lab file, you can download and check it. HUB:interface Tunnel1no shutdownip address 10...
In my lab NAT Overload is not working when applied to the interface but it does work when I apply a NAT IP Pool. What configuration am I missing here?
On a IOS-XE v17.06.05 router, I uploaded the NBAR2 pack and pointed to it with command. ip nbar protocol-pack bootflash:pp-adv-cat8k-179.1a-46-65.0.0.pack But it shows inactivate...How would I be able to activate it to replace the default one? Is it ...
